Skanska USA Civil Northeast, Inc.

An employee was cutting plywood strips for edge forms using a circular saw. The employee was cutting with the plywood nailed down to the table and two hands on the saw. While cutting, the saw bound up momentarily. The employee lost his grip and brought his left hand to the table to catch himself. At this point, the saw reengaged and amputated the tip of his left index finger.

An employee was loading palleted joint baskets onto a flatbed truck using slings. Baskets on the flatbed began to tilt and the employee fell/jumped from the flatbed. Baskets then landed on their legs and the employee sustained a suspected tendon rupture in the right knee.

At 1:18 p.m. on February 2, 2023, employees were moving an 8-by-10-foot road plate, weighing about 3,000 pounds, using a front loader with a fork attachment. The fork was being used to raise one end of the plate so that dunnage could be inserted between it and the plate it was stacked on. The plate slid off the fork while it was 6 inches off the ground and struck the front of an employee s left foot. He suffered a displaced fracture to the last joint of his left big toe.

An employee broke his leg tripping over light-pole foundation footing while trying to run out of the way of a falling security fence.

An employee was unloading a trailer when a box fell and struck the employee in the face. The employee suffered a concussion and was hospitalized.

An employee had been cutting lumber for a shed wall. A load of 16-foot trim pieces fell onto the employee causing vertebrae and ankle fractures.

An employee was unloading 30-foot 2-inch barrels from a pan holding about 20 barrels. The barrels tipped over, striking and breaking both of the employee's lower legs.

An employee was in a sandblasting area, preparing the surface of a plate heat exchanger frame for painting. The frame fell on the employee, who suffered fractures to vertebrae, the neck, pelvis, and rib cage; and punctured lungs.

An employee was installing doors when one of the doors fell on him, fracturing his lower leg. The employee was hospitalized.

A crew was installing drilled micropiles alongside an outdoor covered deck foundation. The injured employee was working the front of the drill when a loose section of casing dropped onto the tip of a rig wrench and pulled the wrench down to an embedded casing. The employee's left little finger was caught between the rig wrench and the embedded casing and was amputated above the top knuckle.

An employee was standing on an extension ladder, using a torquing tool to remove bolts that secured blades to a rotor. When the torquing tool activated, its reaction arm came around and pinched the employee's right middle finger against a lifting eye. His fingertip was amputated.

Employees were securing the fuel line of an outboard motor in preparation for removing the motor from a small vessel located in the equipment yard. A gasoline-related fire occurred and one employee sustained burns to both hands and forearms.

A marine diver/construction worker was working underwater, using a hydraulic dredge to clear sediment away from the base of a dam. The dredge's suction nozzle began migrating toward him, and then pulled in his right hand and forearm. He sustained compartment syndrome in the hand and forearm.

An employee was standing on a sheet of -inch by 4-foot by 8-foot plywood on top of a rebar mat, supervising his crew. As he was moving to alert the crew to an incoming overhead load, he stepped off the plywood and his left foot slipped through the rebar mat and landed on the rebar mat below. His left ankle was broken and dislocated.

An employee was cleaning leaves with a backpack blower when he fell from a ladder, resulting in injuries to his head, neck, and back.

An employee was operating a battery-powered broom to clean demolition debris off the top of the outermost bridge girder. The girder was approximately 11 feet above the demolition scaffold below. The employee fell approximately 8 feet to wind bracing below. The employee was hospitalized with a pelvis/tailbone fracture. Fall protection was in place at the time.

An employee slipped while descending in a stairwell, fell, and suffered multiple contusions/bruises to the head, neck, shoulders, knees, and back. She was hospitalized.

An employee's right middle finger was caught in a nip point. The employee suffered an amputation to the middle finger at the first knuckle.

An employee was directing trucks as they entered and left a highway work zone. A vehicle struck them, resulting in multiple fractures and other injuries. The employee was hospitalized.