HD Supply Construction Supply, Ltd.

A delivery driver was lifting bundles of wire mesh off a flatbed trailer using a truck-mounted lift. As he was lowering the mesh, the lift tipped over and ejected him forwards. He landed on the ground and was injured.

An employee was operating a bar bending machine when his finger was caught between the rebar and mandrel bender wheel, resulting in a right index finger amputation just above the first digit behind the fingernail.

An employee was bending rebar on a fabrication/bending machine when his right pinky finger was caught between the two ends of a piece of rebar as the ends overlapped to form a circle. The employee's fingertip was amputated.

An employee was walking to the front door, slipped on ice and fell to the ground resulting in injury to their left side.

An employee was walking in the rebar shop when he fell to the floor, suffering facial contusions and an injury to the vertebrae in his neck.

An employee was tossing a damaged toilet into a compactor. The toilet bounced off the compactor and lacerated the employee's right wrist, cutting an artery and tendon.

An employee was operating a hydraulic jack to bend a frame when the jack came loose and struck the employee. They were hospitalized for a spleen injury.

A truck had been towed into the shop with a flat tire and a blown airbag. An employee checked the tire for damage and was airing the tire. The employee was installing the valve core when the bead slipped off the rim. Air escaped, and the aluminum wheel struck the employee's head and face. The employee became unresponsive and was bleeding.

On December 14, 2023, at 8:40 p.m., three employees were inspecting milling machines for startup. A few of the sleeves on the mill drum needed to be changed out. The injured employee was trying to input a sleeve on the mill drum using a hammer. The hammer hit the edge of the drum, which caused a metal piece to splinter off and strike the employee's cheek just below the left eye. The metal splinter embedded in the back of their eye socket, resulting in pain, swelling, and bleeding that required hospitalization.

An employee was pushing a line of carts into a vestibule when the door cable snapped and struck his right ankle. The employee suffered a fracture that required surgery and hospitalization.

An employee was unloading freight from a truck when a stack of doors fell over and knocked the employee to the ground. The employee sustained a fractured femur.

An employee was performing rebar fabrication using a bending machine. The employee's glove became caught in the area where the rebar bend overlaps onto itself. The subsequent bending/cutting caused the two overlapping portions to squeeze together and amputate approximately 1/4" of his left index fingertip.

An employee was building wood detail blocking and a wood member needed to be resized. The employee took the wood member to the table saw and set the fence to the correct size. The employee pressed down on the board to control it when his left little finger contacted the running blade, resulting in an amputation.

An employee was clearing a pipe along a culvert using a motorized plumbing machine. The end of the machine got tangled and stuck in long grass and other debris. The employee went to lift the end of the machine out of the grass and clear the blockage when his hand was pulled into the machine, resulting in a partial amputation and open fracture of his left distal phalanx.

An employee was operating a router when it cut his right little finger, causing an amputation through the bone.

A crew was installing drilled micropiles alongside an outdoor covered deck foundation. The injured employee was working the front of the drill when a loose section of casing dropped onto the tip of a rig wrench and pulled the wrench down to an embedded casing. The employee's left little finger was caught between the rig wrench and the embedded casing and was amputated above the top knuckle.

Two employees were working to change a tire on a mobile slasher saw. The slasher weighs around 2,000 pounds and is towed. Employee 2 was lifting the saw while the injured employee was placing a block of wood under the frame for support. The slasher then lowered onto the block and the injured employee's left thumb was crushed between the slasher frame and the wood block, leading to an amputation at the first knuckle.

An employee was using a metal shear when it amputated the tip of his right index finger.

An employee was using a crane to move a 44-foot, 3,343-pound I-beam. As the beam was moving west, it straightened out (north to south), beginning to swing south toward the northwest corner of a building. The crane then sent the beam southward, directly toward the corner of the building. The beam caught the tips of the employee's left index, middle, and ring fingers against the building. The last joints of the middle and ring fingers were amputated, and the last joint of the index finger was partially crushed.

An employee was standing on a step stool, removing the nuts and bolts from the frame of a solar panel that was being replaced. The employee's cheek made contact with a connector with damaged insulation. The employee was shocked, briefly lost consciousness, and fell to the ground, suffering an injury to the left shoulder.