Stanley Black and Decker

An employee was walking up the stairs in an office area. Their right foot caught the edge of the stair at the top of the stairwell and they fell forward. The employee sustained a neck fracture.

An employee was performing continuity testing on an HVAC connection when an arc flash occurred. The employee sustained burns to their face and both hands.

An employee was moving a coil of metal with a crane using a C-hook. As he was moving the hook, his left hand was caught between it and a second coil of metal on the floor. His middle finger was pinched between the spine of the C-hook and the edge of the metal coil on the floor. He suffered an amputation to the flesh at the tip of the finger, as well as a fracture to the fingertip.

An employee rotated an arbor into position for the next setup of the slitter. The inward movement pinched the employee's left thumb between the arbor and the arbor lock. The employee's left thumb was medically amputated just below the knuckle.

An employee was stepping down from the back of a shuttle/vehicle and landed awkwardly resulting in a fractured ankle.

On November 17, 2023, a maintenance employee opened a line and residual bromine was released. The employee sustained burns to their palm and left leg and also suffered an inhalation injury.

An employee was picking up trash bags on a route and putting the bags in the back of a garbage truck. The employee was compacting the trash when one of the bags released vapor and dust from chlorine and pool cleaning chemicals. The vapor and dust contacted the employee's eyes and mouth and were inhaled. The employee was hospitalized with chemical irritation to the eyes and lungs.

On June 2, 2023, an employee was re-installing a repaired valve. When the employee applied pressure to the system to test the repair, air that contained peracetic acid (PAA) residue flowed from the tote filling wan. The employee contacted the PAA mist, resulting in hospitalization for second-degree chemical burns to the face, swelling of the lips and throat, and irritation to the lungs.

An employee was pouring a copper food additive into a bucket when the product splashed into his eyes and face. The employee also inhaled and ingested the substance. The employee suffered copper poisoning.

An employee was rebuilding a valve on a refrigeration system and had pumped down the ammonia in the system to conduct maintenance. He removed a cover and was sprayed by residual anhydrous ammonia. The employee sustained chemical burns to the face and hands and may have sustained a respiratory injury.

An employee was backing up an electric pallet jack when it struck a yellow guardrail, pinning his ankle between the pallet jack and the guardrail. The employee suffered a crush injury to his left ankle and shin.

The injured employee was going to use an elevator to go upstairs. The elevator does not have a call button and is operated manually. The employee approached the elevator and used the elevator drop key located in the elevator key box to manually open the door. He then stepped forward into the elevator shaft. The elevator car was on another floor, resulting in the employee falling down the shaft from the first floor to the basement level. The employee was hospitalized with a sprained left hand and bilateral calcaneal fractures.

An employee was aligning a shipping offload conveyor. A component of the machine caught the employee's left middle finger, amputating it above the second knuckle.

An employee was using a torch to burn off liquid petroleum gas from old 100-pound cylinders so they could be recycled. When he went to move a tank, some gas spilled onto the ground, then ignited in a flash that engulfed him. He was burned on the face, hands, and back and was hospitalized.

An employee was escorting a forklift inside a store. While walking backward, the employee tripped on a pallet and fell, suffering a broken hip.

A crew was installing drilled micropiles alongside an outdoor covered deck foundation. The injured employee was working the front of the drill when a loose section of casing dropped onto the tip of a rig wrench and pulled the wrench down to an embedded casing. The employee's left little finger was caught between the rig wrench and the embedded casing and was amputated above the top knuckle.

Two employees were working to change a tire on a mobile slasher saw. The slasher weighs around 2,000 pounds and is towed. Employee 2 was lifting the saw while the injured employee was placing a block of wood under the frame for support. The slasher then lowered onto the block and the injured employee's left thumb was crushed between the slasher frame and the wood block, leading to an amputation at the first knuckle.

An employee was using a metal shear when it amputated the tip of his right index finger.

An employee was using a crane to move a 44-foot, 3,343-pound I-beam. As the beam was moving west, it straightened out (north to south), beginning to swing south toward the northwest corner of a building. The crane then sent the beam southward, directly toward the corner of the building. The beam caught the tips of the employee's left index, middle, and ring fingers against the building. The last joints of the middle and ring fingers were amputated, and the last joint of the index finger was partially crushed.

An employee was standing on a step stool, removing the nuts and bolts from the frame of a solar panel that was being replaced. The employee's cheek made contact with a connector with damaged insulation. The employee was shocked, briefly lost consciousness, and fell to the ground, suffering an injury to the left shoulder.