DHL Inc

An employee was changing the battery on his forklift. He removed the forklift's battery plate and exited the battery machine alignment track. The shift lead then went to retrieve a new battery. The employee entered the battery machine alignment track again to unplug the charging cable. The battery changing equipment proceeded forward and pinned the employee against the forklift. The employee was hospitalized with two fractured ribs.

A crew was working near an electrical pole. A co-worker was using a front-loader to grade a slope when the loader slid into a guy-wire and became tangled and stuck. The injured employee used a handheld grinder to cut the wire a few feet from the ground. The lower part of the wire fell to the ground, but the upper part of the wire fell toward the pole and contacted an energized part before the end landed in nearby bushes. The employee attempted to shake the bush to free the wire so it could fall back toward the pole. The wire popped up and contacted his hands, resulting in electrical entry burns to both hands and exit burns on both feet.

On November 18, 2023, two employees were using a 2x4 to lift a power line. The boom lift they were operating made contact with power lines and both employees sustained electrical shock injuries.

An employee was part of a crew that was servicing a power line. The employee was in a bucket truck when he contacted the 7,200-volt power line. The electricity entered through one hand and exited the other, causing several electrical burns. The employee was not wearing proper personal protective equipment at the time.

An employee was helping a crew set up a 45-foot pole between two other poles. It was being set up between two energized lines and the pole made contact with the A-phase. The employee was electrocuted and lost consciousness. The electricity also caused an entry wound in their left forearm and an exit wound in their left foot.

An employee was handling a 45-foot long rebar for installation on the third floor of a building at a 30-foot elevation. The rebar came into close proximity of a powerline situated 13 feet off the building. The employee sustained electrical burns to his hands from electric discharge, requiring hospitalization.

An employee was retrieving a water bottle from the operator compartment of a unit load device transporter. The transporter accelerated and ran over her foot, causing lacerations to the skin surrounding her toes that required hospitalization and surgery.

An employee had been accessing the cargo door to load an aircraft. They fell 15 feet from an aircraft belt loader to the tarmac. The employee was hospitalized with injuries to both arms.

An employee was standing on the back bumper of a package car as another employee was backing up the vehicle. Their toes were crushed between the dock leveler and the bumper of the vehicle. The employee sustained fractures to their foot and toes and required surgery.

An employee was tying down air pallets onto a dolly when a nearby forklift reversed and struck a transfer dolly, which then hit the dolly that the employee was working on. The air pallet dolly subsequently struck the employee and knocked him over, resulting in hospitalization for pain in their lower back, left hip, thigh, and leg.

An employee was opening a zip tie using a knife. The knife slipped and cut the employee's left index finger, resulting in a partial amputation (without bone loss) to the fingertip.

An employee was delivering materials. He was doing his pre-delivery inspection on the roof of the jobsite (a warehouse) when he fell through a plexiglass skylight. He landed on his feet on the concrete floor 14 feet below. The employee sustained fractures to his spine, left ulnar/radius, and right heel. The employee required surgery.

An employee was cutting cabinet trim using a table saw when four fingers on his left hand were severed, resulting in hospitalization and amputation.

An employee was removing packaging from a roll of printing substrate. The blade of their utility knife got stuck. The employee used both hands to free the knife and the blade partially amputated their left little fingertip.

A concrete batch plant operator was assisting with clearing spoil piles using a skid steer. The skid steer backed into a stationary screen plant. The employee's left little finger was crushed between the controls of the skid steer and the screen plant, resulting in a fracture and laceration. The employee's finger was surgically amputated.

An employee was standing on an extension ladder, using a torquing tool to remove bolts that secured blades to a rotor. When the torquing tool activated, its reaction arm came around and pinched the employee's right middle finger against a lifting eye. His fingertip was amputated.