Shelby Erectors, Inc.

An employee was on a deck on an elevated section of an interstate, shaking out some pans. The employee fell to the ground, suffering broken bones.

An employee was working on a bridge deck when he walked across an unsecured deck mat and it slid, causing him and the mat to fall approximately 30 feet to the road surface below. He suffered arm, leg, pelvic, and skull fractures; liver bleeding; and a concussion.

An employee was sitting in the cab of the truck while waste oxidizer was being offloaded. The waste reacted with the receiving tank and an explosion occurred in the tank. Fire traveled through the hose to the tanker truck, causing it to explode. The employee jumped from the burning truck and was hospitalized with burns to his face, chest, and arms.

An employee was installing piping and valves for fire protection systems in the vicinity of an electrical meter outside of a new warehouse. The meter exploded, causing burns to the employee's face and arms.

An employee was pouring molten aluminum into a drain pot. The aluminum touched moisture at the bottom of the drain pot and an explosion occurred. The employee sustained burns to their face, hands, and legs.

An employee was operating an oxygen-deficient oven that required manual ignition to make charcoal from wood. As the oven was opened, oxygen was introduced to the environment, resulting in an explosion. The employee sustained head trauma as well as fractures to the arms and legs.

An employee was setting up the electrical parts for a fireworks display. They were inserting an e-match when it generated friction with something else. A 3-inch firework shell ignited, injuring the employee's hand and head.

An employee fell from a step ladder while reaching for a tie-off point. He impacted the ground, and landed on his bolt bag which contained tools. The employee was hospitalized with fractured ribs, and a lacerated spleen and kidney.

An employee was attempting to lift a steel beam from a horizontal, stacked position to a vertical position using a crane. They had placed two hooks on the east side of the beam on the flange. As the employee was hoisting the crane, the beam began to shift and pulled the employee forward onto the stack. When the material shifted, the hooks released and the material fell, pinning the employee between the two beams. The employee was hospitalized with soft tissue contusions on their proximal right thigh and interior left thigh.

An employee was standing on the surface of a steel beam about two feet wide. He slipped and fell backward, landing on the concrete ground about 20 feet below. The employee sustained a broken pelvis.

An employee was unloading a rebar delivery from a flatbed, 19-wheel trailer. The employee rigged the load with wire rope chokers. The load was picked up 3-4 feet above the trailer deck by a crane. The load began to swing and the employee grabbed onto it to prevent it from being pushed off the trailer deck. The crane continued to lift the load, and the employee let go so the crane did not lift him to the third story. The employee fell approximately 12 feet to the ground below, resulting in a back injury and fractured vertebrae.

An employee was attaching a steel angle plate weighing (approximately 200 pounds) to the end of a structural member (5,000 pounds) and was supported by dunnage. The dunnage was a crane mat (11 inches tall) with a 4x6 board on top of it and it supported five identical members. The main piece was 30.75 feet long, 37.25 feet tall, and 1 food wide. As the employee slid the piece of metal on top of the member to begin attaching it, the entire member began to tip over. The employee went to stop the main piece from tipping over and it landed on his ankle, fracturing it.

An employee was helping a coworker transport a tall palm tree with a mini skid steer. The employee was severely shocked by a high-voltage electrical wire above the ground.

An employee was retrieving a Christmas tree from a shelf using a ladder. He missed a step and fell to the concrete floor. He sustained injury to his head and wrist.

An employee was inspecting a generator whose radiator was leaking. He slipped, and a fan blade in the generator amputated his thumb and index finger.

An employee was operating an agricultural tractor during sugarcane harvesting. The employee sustained a lumbar sprain due to vibration or motion from the tractor.

An employee was moving a 3-ton condensing unit, strapped down on a dolly, out of a garage. The strap broke, causing the employee to fall backward onto the brick pavered driveway. The employee suffered injury to a spinal ligament in the neck.