Acme Manufacturing Company, Inc.

An employee was reaching to get some paperwork when the center drive chain of a powered roller conveyor caught his left glove. The chain pulled in the glove and his little finger, then partially amputated his index finger.

Two employees were trying to right an overturned pallet of 10-foot angle iron using a forklift. One employee's left middle finger was caught between the pallet of angle iron and another pallet below. The employee suffered an amputation to the fingertip.

On November 27, 2023, an employee was emptying a 2-inch product line that transports sodium hydroxide liquid from a rail car to a 275-gallon tote tank. The nozzle came out of the tote and sprayed sodium hydroxide onto the employee's face. The employee was hospitalized with chemical burns to their face, mouth, and neck.

An employee was working with sulfuric acid as part of the production process. While transferring the chemical from a large container to a smaller container, it splashed on his body and hand, resulting in a chemical burn.

An employee knelt in wet concrete while performing work as a concrete finisher and sustained a chemical burn to the right shin. The employee was hospitalized and required surgery.

An employee was using a 5-gallon bucket to unload acid product from a tank. Residual product leaked into the containment area, causing the employee to sustain first- and second-degree burns to the chest, as well as third-degree burns to the arms.

An employee was transferring an alkaline cleaning chemical from a bulk container into 1-gallon containers. The employee lifted a gallon container by its label tag. The tag broke causing the container to fall approximately 14-18 inches. The container struck the ground and the contents splashed onto the employee causing chemical burns to their eyes.

An employee fell while entering the building. The employee was hospitalized with a fractured ankle and required surgery.

An employee was doing a cable change on top of an electric overhead traveling (EOT) crane. They were positioned between the cable drum and the drive shaft. While rotating the cable drum, the employee reached for the new cable that was to be installed. The grease fitting on the drive shaft caught their fall harness and pulled them underneath the drive shaft. The employee was pinned between the drive shaft and two pieces of angle steel, resulting in a fracture to their left hip.

An employee was working to close a furnace door. The hydraulic mechanism that opens and closes the furnace door was non-operational and had been disconnected to allow the furnace door to be opened manually. As the employee was releasing the pins that held the door open, the door and the hydraulic cylinder fell, pinching their left hand between the hydraulic cylinder's base plate and the furnace. The employee suffered amputation of the little fingertip.

A rolling mill was shut down due to a cobble between two mill stands. The injured employee was cleaning the cobble from the delivery side of stand A, while another employee went to the control panel to move stand B and stand A moved instead. The injured employee's right thumb got caught between the delivery guide of stand A and the looper trough. The tip of his thumb required surgical amputation to the bone to allow for stitches.

An employee was helping another employee load stock material onto a press brake when the stock slipped. The injured employee's right index finger was caught between the press brake die and the stock, resulting in amputation at the first knuckle.

An employee was delivering materials. He was doing his pre-delivery inspection on the roof of the jobsite (a warehouse) when he fell through a plexiglass skylight. He landed on his feet on the concrete floor 14 feet below. The employee sustained fractures to his spine, left ulnar/radius, and right heel. The employee required surgery.

An employee was cutting cabinet trim using a table saw when four fingers on his left hand were severed, resulting in hospitalization and amputation.

An employee was removing packaging from a roll of printing substrate. The blade of their utility knife got stuck. The employee used both hands to free the knife and the blade partially amputated their left little fingertip.

A concrete batch plant operator was assisting with clearing spoil piles using a skid steer. The skid steer backed into a stationary screen plant. The employee's left little finger was crushed between the controls of the skid steer and the screen plant, resulting in a fracture and laceration. The employee's finger was surgically amputated.

An employee was standing on an extension ladder, using a torquing tool to remove bolts that secured blades to a rotor. When the torquing tool activated, its reaction arm came around and pinched the employee's right middle finger against a lifting eye. His fingertip was amputated.