Compressed or pinched by shifting objects or equipment · Fractures
At a glance
Federal OSHA recorded a severe workplace injury
at Pratt & Whitney, 8801 MACON RD., COLUMBUS, GEORGIA 31908
on — Fractures, affecting the chest, except internal location of diseases or disorders.
Final narrative
Two maintenance employees were disconnecting utility lines to remove a large oven. The injured employee was lying on his right side applying a valve lock device beneath the oven when his coworker cut the compressed air line, releasing the residual air pressure and allowing the door to glide down and pin the employee to the floor. The employee was hospitalized with rib compression fractures.
HospitalizedChest, except internal location of diseases or disordersMetal, woodworking, and special material machinery, unspecified
An employee was reassembling a tool that consisted of a tube, an inner cylinder, and a cap that is used for engine assembly. The inner cylinder became wedged on the outer cylinder and while pushing down on the inner cylinder with the cap, it descended and caught the employee's right middle finger between the cap and the outer cylinder. This resulted in a partial amputation and fracture to the finger.
The employee was replacing an O-ring that sits on top of a hydraulic oil accumulator tank. The O-ring seals the accumulator tank and the oil manifold to the central cylinder, which had been removed for repair. The employee used a hydraulic jack to raise the oil manifold approximately 1 inch to allow for installation of the O-rings and the central cylinder. The jack slid from its position and the manifold dropped back to its normal resting position, striking and pinching the employee's right thumb. The employee sustained a fracture and open laceration to the thumb, near the knuckle joint.
An employee was installing test equipment on an engine and climbed a 6-step ladder to remove the electrical connectors. As the employee was reaching to disconnect the electrical connector, the ladder pushed outward from underneath the employee. The employee then fell 5 feet from the top step and suffered a contusion, concussion, and chest abrasion.
An employee was removing debris from a machine while waiting on the machine's cooling process to be completed. Due to a software error, the interlock system failed, allowing the machine's die to move and contact the employee's right thumb, which suffered an open fracture. The thump tip had to be medically amputated.
An employee was operating a forklift and unloading a truck. After the truck was unloaded, the employee got off the forklift and proceeded to adjust the dock plate with a hook tool. The dock plate slipped and the employee went to adjust the plate with their hand when their left middle finger got caught. Their finger was amputated above the first joint.
An employee was rotating a carbide granulator blade when his finger was caught between the blade and a stationary part of the machine. The employee's right middle finger was partially amputated and they suffered an avulsion to the right ring fingertip.
An employee was using a CNC metal lathe machine in manual mode to check that the thread blocking tool made contact with the jaws. As the employee was manually spinning the spindle, his index fingertip was crushed between the spindle's jaws and the grooving insert, resulting in a fingertip amputation.
During a material handling operation, an employee's fingertip was caught under an air conditioning unit as the unit was lowered onto a cart. The employee's fingertip was amputated.
An employee was removing a bolt from a tractor hub when their right index finger was caught between the hub and the frame. The employee's fingertip was crushed and the employee was hospitalized.
More severe injuries in this industry (NAICS 336413)
An employee was walking from one building to another when he slipped on wet concrete and fell. The employee was hospitalized with a fracture and dislocation of the right patella.
An employee was working inside the access panel of a sliding door when the door began to shut. The employee's left middle finger was pulled into the chain and sprocket, resulting in amputation to the middle knuckle.
An employee was installing a rail on a machine. The roller pack was locked up, causing the chuck to not move. While manually removing the chuck, the rails were damaged. As a result, both the roller pack and the rail needed to be replaced. A fixed magnet from above the rail pulled the rail up and rolled it, pinching the employee's thumb between the rail and the magnet when he tried to install the new rail back to the position. The right thumb tip was amputated.
An employee was helping to lift the grating from a floor draining system when the grating slipped and landed on his hand, resulting in the amputation of his right middle finger at the first joint.
During a workshop meeting in a hotel, an employee heard a drilling noise, so he walked outside to see what it was. An explosion occurred (possible gas line) and his face, ear, and hair were burned. He also fell and sustained a pelvic fracture.
An employee was using a tool to remove a rag from a roll on the tube mill. The roll pulled the tool and the employee's right hand into the roll, resulting in a partial amputation of the little finger and a fracture to the index finger.