Anthony Timberlands, Inc.

An employee was walking along a catwalk while tracking a section of chain when they fell 7.5 feet to the ground below, resulting in a broken rib, punctured lung, broken collarbone, broken wrist, laceration to head, and a brain bleed.

An employee and a co-worker were removing forks from an unused forklift in order to remove the fork positioners. They removed a pin from the fork and it shifted and swung toward the employee. The employee attempted to jump over the fork, but it struck his foot mid-air, resulting in fractured bones on the top of his foot.

An employee was attempting to remove a board from a landing table when his foot became caught in the drive chain. The employee's toe was amputated.

An employee was transferring 6x6 timber from a roll case in a planar mill when the timber slipped and pinched the employee's right ring finger between it and the roll case guard. The employee suffered a right ring fingertip amputation.

An employee was walking when he fell near the chip chain by the bind. His right hand was caught in the belt at the drive of the chip chain bend, resulting in a pinky finger amputation.

An employee was transitioning from a ladder onto a roof when the ladder slipped and they fell approximately 20 feet to the ground. The employee was hospitalized with fractures to their pelvis and heel.

An employee was tearing down shingles when they fell approximately 18 feet from a roof to the ground, sustaining a broken ankle.

An employee was climbing a ladder to bring material onto a roof. The ladder slid and the employee fell 16 feet to the ground, resulting in a broken knee.

An employee was performing an inspection of a bridge crane while working from a 19-foot scissor lift. The employee was going to use a pendant to move the crane to access a different portion of the crane for visual inspection. The scissor lift guard rails were below the girder of the crane to avoid contact. The tow arm for the crane collectors contacted the guardrail of the scissor lift and caused it to tip over. The employee stayed inside the scissor lift basket as he fell to the floor. The employee sustained fractures to the right arm and hip.

An employee was on a forklift that was elevated approximately 20 feet and was auditing inventory. The forklift malfunctioned and the employee fell down to the surface below, causing them to sustain multiple fractures.

An employee was repairing a photo eye on the infeed roll case when they dropped a tool. The employee went to grab the tool and his fingers contacted the chain and sprocket of the infeed roll case. His fingers were pulled into the pinch point and the fingertips were crushed, resulting in amputation of one fingertip.

An employee was troubleshooting dispersing equipment. A belt and pulley system was energized, and the moving belt caught the employee's right ring finger. He suffered a partial amputation at the first knuckle, below the nail.

An employee was cleaning the photo eye sensors of a piece of equipment between the saw that cuts lumber into lengths and boards. The employee stepped on a metal grate that gave way and fell 8-10 feet. The employee was able to remove himself from the conveyor. His tibia was fractured just below the knee.

An employee was working to get a log back onto a carriage. The employee came into contact with the running saw, which amputated their arm.

While refilling a lubricant tank, an employee observed that a pump was not operating correctly. While troubleshooting the issue, the employee reached toward the back of the pump to check for proper airflow. Their left index finger contacted moving components in the pump's piston mechanism, resulting in partial amputation of the fingertip.

An employee was operating an ironworker (steel punching/shearing) machine. A piece of the tooling broke off and struck the employee's neck; a fragment was lodged in his neck. The employee was hospitalized and required surgery.

On October 25, 2025, an employee was stringing up a new reel of tire tread on a machine. The employee pulled a 6-inch tail and proceeded to spool up the liner. As the machine was jogged to begin the liner wrapping process, the liner caught the employee's glove and pulled their right arm into the liner, causing a fracture to the arm.

An employee was doing a cable change on top of an electric overhead traveling (EOT) crane. They were positioned between the cable drum and the drive shaft. While rotating the cable drum, the employee reached for the new cable that was to be installed. The grease fitting on the drive shaft caught their fall harness and pulled them underneath the drive shaft. The employee was pinned between the drive shaft and two pieces of angle steel, resulting in a fracture to their left hip.

An employee was helping two other employees to push a pallet of tile on a loading dock. He suffered a broken fibula and was hospitalized.

On October 5, 2025, an employee was pulling a pressure washer hose when it it disconnected from the cooker. The employee was struck by jets of high-pressure water, resulting in lacerations to their left thigh requiring surgery. The employee was hospitalized.