Anthony Timberlands, Inc.

An employee was walking along a catwalk while tracking a section of chain when they fell 7.5 feet to the ground below, resulting in a broken rib, punctured lung, broken collarbone, broken wrist, laceration to head, and a brain bleed.

An employee was attempting to remove a board from a landing table when his foot became caught in the drive chain. The employee's toe was amputated.

An employee went onto a rollcase to try and release a board that was trapped inside the outfeed rollcase of an edger machine. He lost his balance and fell 10 feet onto a steel waste chute, then slid an additional 10 feet to the bottom of the chute. He suffered a fractured pelvis and broken ribs, as well as a laceration above the eye.

An employee was transferring 6x6 timber from a roll case in a planar mill when the timber slipped and pinched the employee's right ring finger between it and the roll case guard. The employee suffered a right ring fingertip amputation.

An employee was walking when he fell near the chip chain by the bind. His right hand was caught in the belt at the drive of the chip chain bend, resulting in a pinky finger amputation.

An employee was drying and finishing vehicles when a vehicle door closed on their left middle fingertip and amputated it.

An employee was climbing down from a tractor trailer bed when they lost their footing and grabbed onto the roll-up door to stop the fall. The roll-up door then fell onto the employee's hand, resulting in a hand fracture that required surgery.

An employee was attempting to remove a tarp from a flatbed trailer when the trailer handle struck the employee in the chest, resulting in two broken ribs and a punctured lung.

An employee was near a backhoe while the operator was getting a broom. The broom handle struck the lever that actuates the swing of the backhoe bucket. The bucket then struck the injured employee, pinning him to the outrigger. The employee suffered crush injuries to the chest.

The injured employee was being trained on loading trucks in the load out bay. The injured employee and his supervisor climbed the stairs that run parallel to the truck and trailer, walked to the upper platform used for observation and sample taking, and saw that the lid of the grain trailer was closed. The employees began working to open the lid which appeared to be stuck due to cold weather. The injured employee pulled on one of the pivot arms that connect the lid to the main body of the trailer. As the lid began to open, the employee s right hand slipped down on the pivot arm and his index finger was caught between the pivot arm and the base of the pivot arm. The employee s right index finger was fractured and three nerves were severed. The employee was hospitalized.

An employee was repairing a photo eye on the infeed roll case when they dropped a tool. The employee went to grab the tool and his fingers contacted the chain and sprocket of the infeed roll case. His fingers were pulled into the pinch point and the fingertips were crushed, resulting in amputation of one fingertip.

An employee was troubleshooting dispersing equipment. A belt and pulley system was energized, and the moving belt caught the employee's right ring finger. He suffered a partial amputation at the first knuckle, below the nail.

An employee was cleaning the photo eye sensors of a piece of equipment between the saw that cuts lumber into lengths and boards. The employee stepped on a metal grate that gave way and fell 8-10 feet. The employee was able to remove himself from the conveyor. His tibia was fractured just below the knee.

An employee was working to get a log back onto a carriage. The employee came into contact with the running saw, which amputated their arm.

While refilling a lubricant tank, an employee observed that a pump was not operating correctly. While troubleshooting the issue, the employee reached toward the back of the pump to check for proper airflow. Their left index finger contacted moving components in the pump's piston mechanism, resulting in partial amputation of the fingertip.

An employee was operating an ironworker (steel punching/shearing) machine. A piece of the tooling broke off and struck the employee's neck; a fragment was lodged in his neck. The employee was hospitalized and required surgery.

On October 25, 2025, an employee was stringing up a new reel of tire tread on a machine. The employee pulled a 6-inch tail and proceeded to spool up the liner. As the machine was jogged to begin the liner wrapping process, the liner caught the employee's glove and pulled their right arm into the liner, causing a fracture to the arm.

An employee was doing a cable change on top of an electric overhead traveling (EOT) crane. They were positioned between the cable drum and the drive shaft. While rotating the cable drum, the employee reached for the new cable that was to be installed. The grease fitting on the drive shaft caught their fall harness and pulled them underneath the drive shaft. The employee was pinned between the drive shaft and two pieces of angle steel, resulting in a fracture to their left hip.

An employee was helping two other employees to push a pallet of tile on a loading dock. He suffered a broken fibula and was hospitalized.

On October 5, 2025, an employee was pulling a pressure washer hose when it it disconnected from the cooker. The employee was struck by jets of high-pressure water, resulting in lacerations to their left thigh requiring surgery. The employee was hospitalized.