Madison-Kipp Corporation

The injured employee was connecting a scrap conveyor because of a machine startup. They were connecting a plug above their head. A die-cast case cell had a malfunction while making a part and the die-cast machine ejected molten aluminum that struck the injured employee approximately 25 feet away. The employee sustained second- and third-degree burns to their left leg.

An employee was operating a forklift when his foot was crushed between the forklift and a stationary object. The employee sustained crush injuries that required hospitalization.

An employee was hammering a piece of the die cast machine to flatten it out or flush into place when the brass hammer slipped from the employee's grip. As they went to catch it, the employee's right ring finger was caught between the brass hammer and the sliding pin of the die cast machine. The employee's right ring finger was partially amputated.

An employee was installing wood trim surrounding a skylight inside a home. While holding a piece of trim in it's desired location, his pneumatic nail gun discharged, sending a 3/4-inch pin nail into his left forearm.

An employee removed a safety valve on a trailer that unknowingly contained nitrogen gas. The gas released from the trailer and pushed the employee backward off a scaffold approximately 10 feet before they struck a garage door, resulting in a pelvic injury.

An employee was sitting at her workstation when a nail gun malfunctioned and shot a nail into her left leg. She suffered a puncture and blood vessel injury and was hospitalized.

On November 25, 2023, an employee was using a high-pressured water hose to perform sewer line cleaning operations. The employee's right little finger and palm were lacerated by pressurized water from the hose.

An employee was hydroblasting when they slipped and the pressurized water stream lacerated their left ankle.

An employee was working on a control panel for an electric furnace when he sustained an electric shock. The employee was hospitalized.

An employee was trimming manufactured parts using a two-hand control, C-frame trim press. They were manipulating parts in the machine when their hand contacted the controls that energized the machine. The employee sustained amputations to their left index finger and left thumb.

Two employees were operating an aluminum die casting machine when a piston that pushed molten aluminum into the mold stopped dispensing aluminum correctly. After they had spent several hours fixing the issue, the machine cycled and the die closed on one employee's right hand. The employee suffered amputations to the index fingertip and the thumb at the knuckle.

An employee was operating a mold machine when a pouring ladle that was coated with a water-based paste was submerged in molten aluminum. The moisture caused an explosion, resulting in severe burns over his body.

On September 10, 2024, at approximately 5:55 AM, an employee suffered burns to his right hand as he was removing a ladle from a furnace and the cup made contact with the side of the furnace, splashing molten aluminum into his glove. The employee was hospitalized with burns to his right hand.

The injured employee was assisting five other employees with bracing a wall panel that was being stood up. Another employee slipped on frost on the floor surface. The employees went to evacuate the area in anticipation of the wall panel falling over. The injured employee went to jump through a window opening within the wall panel and their lower half was crushed by the falling wall panel. The employee sustained a fractured pelvis.

An employee was using a vertical band saw to cut a thick piece of rubber material. While being cut, the material shifted, causing the employee s right hand to contact the moving blade. The employee's thumb was amputated below the knuckle. The employee was hospitalized, undergoing surgery.

A production sanitation employee was pre-rinsing an incline conveyor and noticed cheese stuck between the belt idler. The employee went to remove the cheese and their glove got caught and pulled their left forearm into the conveyor. The employee's arm was fractured. The machine was not locked out/tagged out at the time.

An employee was on a ladder, taking measurements for a new gutter installation. The ladder slipped out from under him and both he and the ladder fell to the ground. He was hospitalized with seven broken ribs and a broken clavicle.

An employee was unloading a truck for a delivery job. While moving boxes in the truck, the employee tripped over a pallet and fell out of the truck to the ground, resulting in four broken ribs.