Other fall to lower level 6 to 10 feet · Fractures
At a glance
Federal OSHA recorded a severe workplace injury
at Alter Trading Corporation, 4500 WEST BETHANY ROAD, NORTH LITTLE ROCK, ARKANSAS 72117
on — Fractures, affecting the neck, except internal location of diseases or disorders.
Final narrative
An employee was using a manlift to reach a platform and remove material from the infeed conveyor. As he stepped out of the manlift onto the platform he fell about 8 feet and landed on a pile of shredded metals. The employee suffered a C-5 vertebra fracture and was hospitalized.
HospitalizedNeck, except internal location of diseases or disordersManlifts
A truck had dumped a load of scrap metal, and a large piece of pipe rolled under the tandem tire. An employee was standing to the side of the truck (about 15 feet away) as it started to pull away. The tire then rolled over the pipe, causing it to shoot out from under the tire and strike the employee in the shin. The employee suffered a broken leg.
An employee was sorting scrap metal by hand. The employee's finger got caught between a piece of metal and the handrail that it was being tossed over into a bin. The piece landed on the fingertip and pinched it between the rail, resulting in an amputation.
An employee was preparing a tank car for loading while chipping away solidified product in the manway opening of the tank car. A pressure noise within the tank car startled the employee, causing him to stumble backward and fall approximately 10 feet over the guard railing at the chemical loading rack to the ground. The employee suffered fractured vertebrae, a fractured right wrist and ankle, and a dislocated jaw.
An employee was installing an electrical tray remover from a ladder. As he was descending, his missed a step and fell 6-7 feet to the floor. The employee suffered a head injury.
Two employees were installing spray foam insulation in the attic of a new residential construction. The injured employee fell 8 feet from an A-frame ladder to the floor. The employee suffered lacerations, abrasions, and a head injury.
An employee was on a raised platform attaching wires to electrical boxes. The employee fell approximately 8 feet to the floor below and struck an exit sign on the way down, resulting in an injury to his face.
An employee was in a forklift man basket fixing a garage door opener when they fell approximately 8 feet to the concrete ground below. The employee suffered head and back injuries as well as kidney bruising.
More severe injuries in this industry (NAICS 423510)
A load of steel angles was being lowered when the lifting chain hit the load, causing it to slide toward an employee. An angle slid and pinched the employee, catching both of their legs between the beams and an angle. The employee suffered two fractured legs.
An employee was on the deck of a trailer helping a customer unload tubes. The employee was working to place a cargo strap on the remaining tubes using a winch bar when it slipped off the tubing, causing him to lose his balance and fall headfirst onto the asphalt lot below. The employee suffered a contusion on his forehead, resulting in hospitalization.
An employee and a customer were unloading two rectangular tubes. The tubes were wrapped together. The plastic wrap was cut so that one tube could be picked up. As the employee was lifting the top tube, the other tube (still connected to the top tube) came down onto his hand and broke two of his fingers. He was hospitalized.
An employee was assisting as a forklift got pipe from a pipe rack. The employee was on one of the forklift's forks as it was raised to the top of the rack, a height of about 15 feet. He fell to the ground and suffered a dislocated and fractured right elbow.
On September 23, 2025, at approximately 7:43 p.m., an employee was using a knife to cut poly banding from a metal coil. The knife slipped, causing a laceration to the inside of their left arm at the elbow joint. The employee was hospitalized and required surgery to repair a damaged vein.
An employee was operating an ironworker (steel punching/shearing) machine. A piece of the tooling broke off and struck the employee's neck; a fragment was lodged in his neck. The employee was hospitalized and required surgery.
On October 25, 2025, an employee was stringing up a new reel of tire tread on a machine. The employee pulled a 6-inch tail and proceeded to spool up the liner. As the machine was jogged to begin the liner wrapping process, the liner caught the employee's glove and pulled their right arm into the liner, causing a fracture to the arm.
An employee was doing a cable change on top of an electric overhead traveling (EOT) crane. They were positioned between the cable drum and the drive shaft. While rotating the cable drum, the employee reached for the new cable that was to be installed. The grease fitting on the drive shaft caught their fall harness and pulled them underneath the drive shaft. The employee was pinned between the drive shaft and two pieces of angle steel, resulting in a fracture to their left hip.
On October 5, 2025, an employee was pulling a pressure washer hose when it it disconnected from the cooker. The employee was struck by jets of high-pressure water, resulting in lacerations to their left thigh requiring surgery. The employee was hospitalized.