Dustrol Inc.

On December 14, 2023, at 8:40 p.m., three employees were inspecting milling machines for startup. A few of the sleeves on the mill drum needed to be changed out. The injured employee was trying to input a sleeve on the mill drum using a hammer. The hammer hit the edge of the drum, which caused a metal piece to splinter off and strike the employee's cheek just below the left eye. The metal splinter embedded in the back of their eye socket, resulting in pain, swelling, and bleeding that required hospitalization.

An employee was standing on a trailer that was approximately 24 inches from the ground. The employee lost their balance and fell off the trailer, sustaining fractures to both ankles.

An employee was preparing to lift the averaging arm on a milling machine and place it in the locked position so the milling machine could back up and get into position to start a new cut on asphalt. The milling machine started backing up. Another employee grabbed the averaging arm by the end to help the first employee; it raised unbalanced, the opposite end teetered, stuck into the asphalt surface, and the end the second employee was holding lifted. The employee's right index and middle fingers were caught, lacerated, and fractured between the averaging arm and the milling machine. The index finger was medically amputated below the joint and the middle finger was amputated at the tip.

A worker was standing beside a milling machine. His right foot got too close to the milling head and the machine ran over it causing severe lacerations.

An employee was performing oversight for the welding of a pipeline launcher door on a construction project. Two welders were performing arc welding, one on the interior diameter of the pipeline launcher door, and the other on the outside diameter of the launcher door when a flash fire occurred. The injured employee sustained first- and second-degree burns to the face, neck, back, and hands.

While on a scissor lift, an employee was grinding a steel pipe. Sparks from the grinder ignited some nearby rags that had been used to apply coating treatments to the pipe. This fire subsequently ignited the employee's clothing. The employee sustained burns to approximately 46% of their body and was hospitalized.

An employee was working in an area where another company was also working. The other company's employees were using an electric hydraulic pump to remove the bolts of the frac valve. The wiring of the torque wrench and pump unit were then charred and a flash fire occurred. The employee sustained second-degree burns to their face and neck.

On October 17, 2023, an employee was at a sink while using a solvent to unclog a vacuum trap dip tube that contained solids from pinacolborane distillation. During this process, the sink caught on fire and the solvent bottle containing tert-butyl methyl ether fell into the burning sink. The employee attempted to remove the solvent bottle which also caught on fire and suffered burns to their neck and left hand.

An employee was under a railcar cleaning up dust with a vacuum hose. The hose caused a spark that caused a flash fire that ignited the employee's clothing. The employee sustained second- and third-degree burns over 83% of his body.

An employee was operating a battery-powered broom to clean demolition debris off the top of the outermost bridge girder. The girder was approximately 11 feet above the demolition scaffold below. The employee fell approximately 8 feet to wind bracing below. The employee was hospitalized with a pelvis/tailbone fracture. Fall protection was in place at the time.

An employee was cleaning out an inlet pipe in a stormwater structure. The employee stepped back, fell into the pipe, and landed on concrete 13 feet below, at the bottom of the structure. He suffered a broken back.

A concrete batch plant operator was assisting with clearing spoil piles using a skid steer. The skid steer backed into a stationary screen plant. The employee's left little finger was crushed between the controls of the skid steer and the screen plant, resulting in a fracture and laceration. The employee's finger was surgically amputated.

An employee was operating a roller and paving a small pathway next to a pavilion. The ground was on a slight pitch, causing him to reach up toward the roll cage to stabilize himself. His right fifth finger was pinched between the roll cage and the rafter of the pavilion. The employee sustained a partial degloving injury with partial traumatic amputation.

An employee was working with paving equipment and heard a noise on the opposite side of the machine he was working on. When the machine stopped, the employee went to the opposite side and crouched down to investigate the noise. A mini track loader backed up and drove over the employee's leg. The employee sustained fractures to their lower leg, ankle, and foot.

After cutting a slab of beef short ribs, an employee turned to grab the pieces he had cut and his right hand contacted the saw blade. The employee sustained an amputation to his right index finger.

An employee was unloading a carpet pad from a truck when they fell from the truck dock to the concrete below, resulting in five fractured ribs and an injury to their left lung.

An employee was inspecting flares processes. The employee received burns to the front side of the body, face and arm from the flares.

An employee was removing plastic material from a production line when the machine cycled and amputated his left index, ring, and little fingers.

An employee was walking up a walkway to enter a building through the back entrance when she tripped over the lip of the cement ramp. The employee fell and sustained a fractured right hip.