Georgia-Pacific Corrugated LLC

An employee was lubricating a chain and sprocket on a corrugator splicer. He lost his balance, and his right middle finger came into contact with the chain and sprocket. The fingertip was amputated at the nail bed.

An employee was prepping a roll of paper to be ejected from the editor machine. Paper rolled forward and the employee's right index fingertip was crushed between the roll and the ejection table, resulting in an amputation.

An employee was servicing the #128 Rotary Die Cutter. The machine was de-energized and locked out. The employee was using a timing wrench to adjust a bar and belt in the machine. As the employee was twisting the wrench, his finger got pinched between the bar and another part of the machine. The twisting action combined with the pinch point caused the employee to suffer an avulsion to the thumb on his left hand.

An employee was pushing carts into the chute area for customers to retrieve. The first of six carts struck the wall and caused the other carts to bounce back and strike the employee. The carts knocked the employee to the ground and she sustained a back injury.

An employee was loading a portable storage container onto a dovetail trailer. This requires hooking up a bridle to the container and lifting the container enough for the dovetail to begin to slide under it. The employee reached and held the bridle lock to allow the trailer to move under it when the trailer moved backward instead of forward and caught his finger. The employee's right middle finger was amputated between the fingernail and the first knuckle.

An employee was reaching over a small stack of steel billets on the ground to cut a strap. When the strap was cut, one of the billets (weighing 5,182 pounds) rolled down onto his right leg. He was pinned and suffered a broken tibia. The incident occurred while the employee was training.

On June 7, 2023, employees were unloading a box truck and rolling a reel of 2-inch plastic pipe to the back of the truck. As the employees were rolling the reel, the edge of the steel frame of the reel contacted the side of the truck. The injured employee s right little finger was caught between the reel and the truck, resulting in a laceration and fracture as well as a little finger amputation.

Employees were using a dolly to remove a trash compactor unit from a residential home. As they began to transport it out of the room and to the outside, the dolly encountered uneven ground. This caused the dolly and the unit to move quicker than expected. The injured employee's left hand was then caught between a nearby concrete column and the compactor unit, resulting in fractures of the left ring and middle fingers that required amputation.

Tools and parts were being lowered to the ground from an elevated platform in a 5-gallon bucket. The rope being used to lower the bucket failed; the tools and parts fell and lacerated the left forearm and upper left leg of an employee on the ground.

An employee was tracking an infeed belt on a scrap hogger when their right arm was caught between the belt and a roller. The arm was broken and the employee's shoulder was dislocated. The employee was hospitalized.

An employee was working to clear a jam from a paper napkin folder. The ram that advanced the napkins pushed the employee's right arm into the side of the machine, causing several lacerations and a hairline fracture.

An employee was troubleshooting overflowing ink on a printer-slotter machine when their right ring fingertip was caught in a guarded roller, resulting in a partial amputation.

An employee was disconnecting wires in preparation to swap out a refiner motor when they contacted energized equipment and sustained an electrical shock. The employee was hospitalized.

After cutting a slab of beef short ribs, an employee turned to grab the pieces he had cut and his right hand contacted the saw blade. The employee sustained an amputation to his right index finger.

An employee was unloading a carpet pad from a truck when they fell from the truck dock to the concrete below, resulting in five fractured ribs and an injury to their left lung.

An employee was inspecting flares processes. The employee received burns to the front side of the body, face and arm from the flares.

An employee was removing plastic material from a production line when the machine cycled and amputated his left index, ring, and little fingers.

An employee was walking up a walkway to enter a building through the back entrance when she tripped over the lip of the cement ramp. The employee fell and sustained a fractured right hip.