Struck by object falling from vehicle or machinery-other than vehicle part · Amputations
At a glance
Federal OSHA recorded a severe workplace injury
at TMC Enterprises, Inc, 1225 Frisco Cemetery Road, LOWELL, ARKANSAS 72745
on — Amputations, affecting the lower leg(s).
Final narrative
At 9:25 a.m. on November 28, 2022, an employee was helping a co-worker operate a band saw. As he was assisting to remove the unused stock from the support table, another piece of steel bar stock weighing approximately 1,430 to 1,560 pounds came out of the saw's clamp and rolled, causing the table to tip due to the weight. The bar then fell off the table and struck the employee, resulting in crush injuries to the lower leg and foot. The lower leg was surgically amputated.
HospitalizedAmputationLower leg(s)Bars, rods, reinforcing bar (rebar)
An employee was transporting an 800-pound die on a cart from the tool room. The employee was pulling the cart when it struck a metal plate on the floor. This caused the cart to tip forward and the die to slide off the cart. The die struck the employee's left foot and their second toe was amputated.
An employee was using a forklift to load pallets of product on a trailer. He exited the forklift to adjust a pallet by hand. The pallet fell on him, resulting in an injury to the left leg.
An employee was lifting a 500-pound steel counterweight off a pallet using a magnetic hold jib crane. The counterweight detached from the crane and the employee sustained a left foot/toe fracture that required surgery.
An employee was using a pipe wrench to turn a 42-foot-long steel pipe on jack stands to weld the bottom portion. The pipe fell off the stands, striking the injured employee on his left shin. The employee sustained a left leg fracture at the shin area as well as a tibia fracture that required surgery.
More severe injuries in this industry (NAICS 332710)
An employee was positioning dunnage on a trailer while pipe was unloaded from a forklift. A pipe fell and the employee's right thumb and index finger were caught between the pipe and a piece of dunnage. The thumb was crushed, and the index fingertip was amputated.
An employee was using a lifting sling on a crane to move a straight-bar bundle and place it on top of an existing bundle. When moving the lifting sling, it became pinched between the bundle and a wood cleat. The bundle then fell onto the employee's left foot, resulting in crush injuries.
An employee was stacking metal tubes using a forklift. A stack became unstable and the employee got out of the forklift to steady it, instructing his helper to get into the forklift. The forklift movement caused some tubes to fall and strike the employee, resulting in an open fracture of his left hand.
An employee was setting up a flexible gear coupling hub in a lathe, preparing to bore it out to fit a shaft. The hub assembly was not secured in the chuck when the crane support was removed, and the employee's right little finger was caught between the hub assembly and the inside of the lathe. The fingertip was amputated.
An employee was using a crowbar to loosen a flat bar when the crowbar struck the employee's right eye. The employee was hospitalized and required surgery.
An employee was operating an ironworker (steel punching/shearing) machine. A piece of the tooling broke off and struck the employee's neck; a fragment was lodged in his neck. The employee was hospitalized and required surgery.
On October 25, 2025, an employee was stringing up a new reel of tire tread on a machine. The employee pulled a 6-inch tail and proceeded to spool up the liner. As the machine was jogged to begin the liner wrapping process, the liner caught the employee's glove and pulled their right arm into the liner, causing a fracture to the arm.
An employee was doing a cable change on top of an electric overhead traveling (EOT) crane. They were positioned between the cable drum and the drive shaft. While rotating the cable drum, the employee reached for the new cable that was to be installed. The grease fitting on the drive shaft caught their fall harness and pulled them underneath the drive shaft. The employee was pinned between the drive shaft and two pieces of angle steel, resulting in a fracture to their left hip.
On October 5, 2025, an employee was pulling a pressure washer hose when it it disconnected from the cooker. The employee was struck by jets of high-pressure water, resulting in lacerations to their left thigh requiring surgery. The employee was hospitalized.