Arkansas Steel Warehouse, Inc.

On June 6, 2023, employees were operating a slitter machine when the injured employee observed a piece of plastic shim hanging from the machine. As the employee went to remove the shim, the machine released a roll of product onto the arbor, trapping the employee's right hand and amputating the middle fingertip.

A crew was pulling a 4-inch plastic gas pipe off a reel and straightening it for installation. The injured employee stepped up on the trailer to cut the last band holding the pipe in the coil on the reel. As he turned to step off the trailer, the end of the pipe rotated and sprung out of the cage surrounding the coil, striking the employee on the side of the head and knocking him off of the trailer into the roadway. The employee suffered head trauma that required hospitalization.

An employee and a co-worker were performing a pick inside a clear well. They rigged the skid pan that was full of broken concrete. When lifting, the load began to swing toward a wall. The employee tried to stop the skid pan from swinging and was struck by the pan, resulting in fractures to their left hip and wrist.

The employee had just completed refueling a lattice crane that was breaking up material and was winding the fuel hose back into the fuel truck when he was struck by the catwalk/stairs of the crane. The employee was hospitalized with a laceration to his backside, possible internal bleeding, and a broken hip.

An employee was fusing 10-inch black rubber utility pipes together using a pipe fusion machine and could not get the pipes to set correctly. The employee used a nylon strap attached to an excavator to lift one side of a pipe off a steel plate. As his hand was between two pipes, the pipes came back together, partially amputating two of his fingers.

An employee was lifting four bags of a lime blend weighing approximately 10,000 pounds using a crane. The load swung and pinned the employee against a structural I-beam, resulting in fractures to the hip and pelvis.

A temporary employee was carrying a nail gun through the warehouse when it hit his leg, activated, and fired a nail into the leg.

An employee was using a tool to remove a rag from a roll on the tube mill. The roll pulled the tool and the employee's right hand into the roll, resulting in a partial amputation of the little finger and a fracture to the index finger.

An employee was removing a roll (tooling) from a machine when their left little finger was pinched between the roll and the machine, resulting in a partial amputation.

An employee was rolling a piece of steel in the belt of a shape roller machine when his finger was pinched between two pieces of steel. His right ring and middle fingers were amputated.

An employee was cutting a length of steel coil when he noticed the steel might have cross-break defects. He used his gloved hand to feel for and clean the defected spots when his glove got caught in the measuring wheel, which rolls along the top of the steel to ensure accurate cuts. The employee's arm was pulled down into the machine until his body was stopped by a support bar that goes across the machine. The employee's arm was fractured at the elbow and required hospitalization.

An employee was operating an ironworker (steel punching/shearing) machine. A piece of the tooling broke off and struck the employee's neck; a fragment was lodged in his neck. The employee was hospitalized and required surgery.

On October 25, 2025, an employee was stringing up a new reel of tire tread on a machine. The employee pulled a 6-inch tail and proceeded to spool up the liner. As the machine was jogged to begin the liner wrapping process, the liner caught the employee's glove and pulled their right arm into the liner, causing a fracture to the arm.

An employee was doing a cable change on top of an electric overhead traveling (EOT) crane. They were positioned between the cable drum and the drive shaft. While rotating the cable drum, the employee reached for the new cable that was to be installed. The grease fitting on the drive shaft caught their fall harness and pulled them underneath the drive shaft. The employee was pinned between the drive shaft and two pieces of angle steel, resulting in a fracture to their left hip.

An employee was helping two other employees to push a pallet of tile on a loading dock. He suffered a broken fibula and was hospitalized.

On October 5, 2025, an employee was pulling a pressure washer hose when it it disconnected from the cooker. The employee was struck by jets of high-pressure water, resulting in lacerations to their left thigh requiring surgery. The employee was hospitalized.