Bekaert Corporation

On August 1, 2025, at approximately 5:05 AM, an employee was applying a label to a spool of product on a crane when the employee s arm became caught between two points of the crane. The employee was hospitalized with a degloving/avulsion injury to their right arm.

A machine operator was loading a spool of wire into a machine. The spool became stuck. When he pulled on it, the spool came loose from the hoist and fractured his thumb.

At about 7:50 a.m. on February 26, 2022, a dry draw operator was using a welder to cut a piece of wire rod. A pneumatic cutter, part of the welding machine, activated and amputated the employee's right index fingertip just below the nailbed.

An employee welded an ISC spool on a payoff to reconnect the wire. After completing this task, the employee went to the control panel and pressed the start button to begin running the machine. While the machine was running, the employee noticed a loop was in the loose wire on the payoff spool and attempted to twist the loop before the wire closed on the spool, which would have made an "eye" in the wire. This would have created a snarl and caused the machine to stop. The employee was attempting to get the loop twisted out when the wire closed down on the spool with his fingers in between. The fingers (index, middle and ring) of the right hand were pinched between the wire, resulting in a partial amputation of the index finger to the second joint, middle finger to the second joint, and ring finger to the first joint.

An employee suffered an electrical shock when he touched a metal cart that had become energized by an electric welder that was mounted on it. The employee was hospitalized.

A crew was installing drilled micropiles alongside an outdoor covered deck foundation. The injured employee was working the front of the drill when a loose section of casing dropped onto the tip of a rig wrench and pulled the wrench down to an embedded casing. The employee's left little finger was caught between the rig wrench and the embedded casing and was amputated above the top knuckle.

An employee was checking a pole-type transformer tank for leaks. A hydraulic clamping device was lowered onto his right thumb and crushed it against the sharp edge of the bottom of the tank. He suffered a partial transphalangeal amputation to the thumb.

An employee had been cleaning the work area. While lifting a saw, the employee's index finger was lacerated by the saw blade. A tendon was cut and required surgery.

An employee was installing a hydraulic extension cylinder in a tow truck when their leg was caught between the cylinder and the truck frame. The employee was hospitalized with a broken tibia, which required surgery.

An employee was sorting sucker rods. His right hand was caught in the area where the rod hits up against the frame and his index fingertip was amputated just below the nail.

A temporary employee was carrying a nail gun through the warehouse when it hit his leg, activated, and fired a nail into the leg.

An employee was using a tool to remove a rag from a roll on the tube mill. The roll pulled the tool and the employee's right hand into the roll, resulting in a partial amputation of the little finger and a fracture to the index finger.

An employee was rolling a piece of steel in the belt of a shape roller machine when his finger was pinched between two pieces of steel. His right ring and middle fingers were amputated.

An employee was cutting a length of steel coil when he noticed the steel might have cross-break defects. He used his gloved hand to feel for and clean the defected spots when his glove got caught in the measuring wheel, which rolls along the top of the steel to ensure accurate cuts. The employee's arm was pulled down into the machine until his body was stopped by a support bar that goes across the machine. The employee's arm was fractured at the elbow and required hospitalization.

Two employees were loading a roll into an EDT machine. One employee was operating the crane and the other employee was the EDT operator. The crane operator was between the roll and the EDT machine. Both employees were struck by the suspended roll and knocked into the EDT machine wall. Both employees sustained internal abdominal injuries requiring surgery and hospitalization. One employee was fatally injured.

An employee was working to deliver mail to an apartment building. She was waiting for a customer to move, to obtain clearance to the mailboxes. The door swung inward and closed on her right little finger. The top half of her finger was surgically amputated.

An employee fell from a step ladder while reaching for a tie-off point. He impacted the ground, and landed on his bolt bag which contained tools. The employee was hospitalized with fractured ribs, and a lacerated spleen and kidney.

On October 30, 2025, an employee was working to adjust a stackable metal shipping container. As the container dropped into place, it caught the employee's hands in an area between the upper and lower cross-members. The employee suffered a laceration to the left ring finger that required stitches, bruising to the right ring finger, and fractures to the right middle finger that necessitated medical amputation of the fingertip.

An employee was moving a scissor lift through a doorway. The employee was pinned between the scissor lift and the doorframe, sustained a back injury, and was hospitalized.

An employee was setting up communication equipment for a meeting. They were walking and tripped over a speaker on the ground. The employee sustained a leg injury.