Irving Forrest Products

The injured employee was standing at the base of a ladder assisting another employee install a TV on a wall. The TV was dropped, striking the employee. They sustained a head injury.

An employee and a colleague were moving two pieces of rebar when a tie was cut. The employee holding the rebar dropped it while it was above the injured employee's hands, resulting in partial amputation to their left middle finger.

An employee was bracing an extension ladder while his coworker installed a 10-foot, 40-45-pound pipe. The pipe fell onto the injured employee's head and he sustained a hematoma, C3 and C4 vertebral fractures and a forehead laceration.

Three employees were removing equipment from an old fermentation room at a bakery. They were using two bakery dollies to remove metal plates from the floor of the room. One of them was holding one of the metal dollies with his right hand on the side of the dolly, as a plate was being centered on the two dollies. The plate slipped and struck his right thumb, which was amputated near the last joint.

An employee was loading 55-pound ballast bricks into a space on a submarine with help from a co-worker. The co-worker passed a brick to the injured employee when it fell onto the employee's left ring finger, pinching it against a steel bin. The employee sustained a compound fracture of the left ring finger.

An employee was repairing a photo eye on the infeed roll case when they dropped a tool. The employee went to grab the tool and his fingers contacted the chain and sprocket of the infeed roll case. His fingers were pulled into the pinch point and the fingertips were crushed, resulting in amputation of one fingertip.

An employee was troubleshooting dispersing equipment. A belt and pulley system was energized, and the moving belt caught the employee's right ring finger. He suffered a partial amputation at the first knuckle, below the nail.

An employee was cleaning the photo eye sensors of a piece of equipment between the saw that cuts lumber into lengths and boards. The employee stepped on a metal grate that gave way and fell 8-10 feet. The employee was able to remove himself from the conveyor. His tibia was fractured just below the knee.

An employee was working to get a log back onto a carriage. The employee came into contact with the running saw, which amputated their arm.

While refilling a lubricant tank, an employee observed that a pump was not operating correctly. While troubleshooting the issue, the employee reached toward the back of the pump to check for proper airflow. Their left index finger contacted moving components in the pump's piston mechanism, resulting in partial amputation of the fingertip.

A crew was installing drilled micropiles alongside an outdoor covered deck foundation. The injured employee was working the front of the drill when a loose section of casing dropped onto the tip of a rig wrench and pulled the wrench down to an embedded casing. The employee's left little finger was caught between the rig wrench and the embedded casing and was amputated above the top knuckle.

Two employees were working to change a tire on a mobile slasher saw. The slasher weighs around 2,000 pounds and is towed. Employee 2 was lifting the saw while the injured employee was placing a block of wood under the frame for support. The slasher then lowered onto the block and the injured employee's left thumb was crushed between the slasher frame and the wood block, leading to an amputation at the first knuckle.

An employee was using a metal shear when it amputated the tip of his right index finger.

An employee was using a crane to move a 44-foot, 3,343-pound I-beam. As the beam was moving west, it straightened out (north to south), beginning to swing south toward the northwest corner of a building. The crane then sent the beam southward, directly toward the corner of the building. The beam caught the tips of the employee's left index, middle, and ring fingers against the building. The last joints of the middle and ring fingers were amputated, and the last joint of the index finger was partially crushed.

An employee was standing on a step stool, removing the nuts and bolts from the frame of a solar panel that was being replaced. The employee's cheek made contact with a connector with damaged insulation. The employee was shocked, briefly lost consciousness, and fell to the ground, suffering an injury to the left shoulder.