T and S Reinforcing Steel

The injured employee was standing at the base of a ladder assisting another employee install a TV on a wall. The TV was dropped, striking the employee. They sustained a head injury.

An employee was bracing an extension ladder while his coworker installed a 10-foot, 40-45-pound pipe. The pipe fell onto the injured employee's head and he sustained a hematoma, C3 and C4 vertebral fractures and a forehead laceration.

An employee was helping to lift a press roll in to fix an issue that was occurring. A co-worker lost their grip and the press roll fell onto the injured employee's left index finger, resulting in a crush injury and amputation.

Three employees were removing equipment from an old fermentation room at a bakery. They were using two bakery dollies to remove metal plates from the floor of the room. One of them was holding one of the metal dollies with his right hand on the side of the dolly, as a plate was being centered on the two dollies. The plate slipped and struck his right thumb, which was amputated near the last joint.

An employee was loading 55-pound ballast bricks into a space on a submarine with help from a co-worker. The co-worker passed a brick to the injured employee when it fell onto the employee's left ring finger, pinching it against a steel bin. The employee sustained a compound fracture of the left ring finger.

An employee fell from a step ladder while reaching for a tie-off point. He impacted the ground, and landed on his bolt bag which contained tools. The employee was hospitalized with fractured ribs, and a lacerated spleen and kidney.

An employee was attempting to lift a steel beam from a horizontal, stacked position to a vertical position using a crane. They had placed two hooks on the east side of the beam on the flange. As the employee was hoisting the crane, the beam began to shift and pulled the employee forward onto the stack. When the material shifted, the hooks released and the material fell, pinning the employee between the two beams. The employee was hospitalized with soft tissue contusions on their proximal right thigh and interior left thigh.

An employee was standing on the surface of a steel beam about two feet wide. He slipped and fell backward, landing on the concrete ground about 20 feet below. The employee sustained a broken pelvis.

An employee was unloading a rebar delivery from a flatbed, 19-wheel trailer. The employee rigged the load with wire rope chokers. The load was picked up 3-4 feet above the trailer deck by a crane. The load began to swing and the employee grabbed onto it to prevent it from being pushed off the trailer deck. The crane continued to lift the load, and the employee let go so the crane did not lift him to the third story. The employee fell approximately 12 feet to the ground below, resulting in a back injury and fractured vertebrae.

An employee was attaching a steel angle plate weighing (approximately 200 pounds) to the end of a structural member (5,000 pounds) and was supported by dunnage. The dunnage was a crane mat (11 inches tall) with a 4x6 board on top of it and it supported five identical members. The main piece was 30.75 feet long, 37.25 feet tall, and 1 food wide. As the employee slid the piece of metal on top of the member to begin attaching it, the entire member began to tip over. The employee went to stop the main piece from tipping over and it landed on his ankle, fracturing it.

An employee was on a four-step work stand while sanding an area of an aircraft. He was climbing down the work stand when he tripped over an air hose and fell to the level below, resulting in a fractured femur.

An employee was scanning the placards of pallets of mail bundles when a forklift approached from the opposite side and began lowering and pushing his pallet load forward. It struck the pallet the employee was working on, causing it to shift and strike her. She fell to the ground and sustained a left hip fracture that required surgery.

An X-ray machine had lost power and an employee went to replace the power supply. While replacing a cable on the power supply assembly, the employee's right hand contacted the grounding terminals coming out of the back of the power supply assembly and they received an electric shock. The employee was hospitalized.

An employee was servicing equipment and had disconnected a 4-inch line. A proportional control air valve on the equipment actuated, releasing a large volume of air at 99 psi into the 4-inch braided stainless steel line hanging down from the valve. The sudden release of pressure caused the line to whip and strike the employee's face. He was hospitalized due to an orbital bone fracture requiring surgery. The equipment was not locked out/tagged out at the time.

An employee was performing janitorial duties and carrying bathroom supplies when he slipped on a guardrail mounting post and fell on his side. The employee's hip was fractured and required surgery.