Caught in or compressed by equipment or objects, unspecified · Fractures
At a glance
Federal OSHA recorded a severe workplace injury
at Cascade Drilling L.P., 22722 29th Drive SE Suite 228, BOTHELL, WASHINGTON 98021
on — Fractures, affecting the finger(s), fingernail(s), unspecified.
Final narrative
An employee and his crew were performing drilling operations and just made a drill casing connection. While the drill operator was lowering the casing hammer and hose down to the casing, the employee was standing beside them guiding the hydraulic hoses with his left hand. When the operator lowered the casing hammer, the employee's right middle finger was contacted by the drill pin rod inside the casing rail, resulting in a compound fracture.
HospitalizedFinger(s), fingernail(s), unspecifiedOil drilling rigs and machinery
An employee was lowering himself to ground level from a drill rig platform when his left middle fingertip was pinched between the jaw of a hydraulic wrench and a section of the drill rig as the wrench was opened, resulting in an amputation of the fingertip.
An employee was changing mud cups in the hopper cylinders of a concrete pump truck. The cylinders moved and three of the employees fingers were amputated.
An employee was standing on the rig floor next to a polishing unit. His hand was placed on the polishing unit when the pump was lowered, resulting in amputation of their right thumb, ring, and middle fingertips.
An employee was using air to blow out the air wash to the blender and grinder station. As the employee reached to verify that the air wash was clean, the unit pinched and amputated their fingertip.
An employee was retrieving a lost drill pipe with a lifting bail when their left thumb got pinched between the table and handle of the lifting bail while trying to re-thread the pipe to lift it out. The employee suffered an amputation to the left thumb.
An employee was removing a core chuck from a stationary roll when their right ring finger was pinched between the chuck and the roll. The employee's fingertip was amputated.
More severe injuries in this industry (NAICS 237110)
An employee was moving a tensile strength test device with a dolly. The device fell from the dolly onto the employee's right leg, causing a compound fracture.
On October 7, 2025, employees were conducting trenching operations for the installation of a new sewer line system. The excavator's bucket was detached and put inside the trench as it was being exchanged for a different-sized bucket. An employee entered the trench with a shovel to move some dirt located at the front end of the pipe. The excavator bucket shifted and slid, striking the employee s right foot and trapping it against the ground. The employee sustained a fractured right tibia.
Employees were working to dislodge a large truck that was stuck in a rut using tow straps and a front-end loader with the bucket removed. An employee connected the straps to the loader and truck and another employee slowly engaged the loader to close the coupler. The injured employee's arm became caught in a pinch point. The employee was hospitalized with a fractured arm.
An employee was lifting a piece of 30-inch line stopping equipment using a jack screw. A lifting eye weld snapped and the load dropped. The end of the jack screw then landed on the employee's heel and crushed it. The employee was hospitalized.
An employee was drilling a hole into the sealed hold of a vessel so a marine chemist could test its atmosphere. Upon drilling the hole, a gas that was under pressure was released and caught fire at the drill motor, where the employee was holding it. The employee was burned.
An employee was performing restoration activities outside a 45-gallon condensation tank of a boiler system. As they were performing post-maintenance activities after repairing one of the two discharge pumps, one of the discharge valves would not open. The employee closed the intake pump to cool off the system and open the discharge valve. Two employees opened the inlet valve to return the tank to service. After they cracked open the inlet valve, a side wall of the tank blew out, causing the injured employee to suffer steam burns to half their body.
An employee was testing and troubleshooting the gang cylinder valve located in the gang area of the sawmill. The employee's fingertip was amputated by the gang cylinder valve.
An employee was unlocking containers on deck. The employee was de-lashing while standing on the edge of the lid. The lashing bar he was holding came off the cone, causing him to turn 90 degrees and strike a railing behind him. The employee sustained four fractured ribs.
An employee parked a side-by-side on the fixed internal ramp aboard a cargo ship. They exited the side-by-side and went to inspect the cargo below. The side-by-side rolled toward the employee and struck them as they were walking toward the edge of the ramp. The employee was knocked off the ramp and landed on the lower deck approximately 8 feet below. The employee was hospitalized with a fractured shoulder.