Ervin Cable Construction, LLC

An employee was opening a new spool of strand from a wooden reel. When he removed the shipping band, the strand struck him in the right eye.

An employee was working in a bucket truck to put up a cable for a new telecommunication line on a utility pole. The employee was trying to throw the line over the trees when the line got stuck in vegetation and the employee fell 20 feet from the bucket to the ground. The employee suffered a broken leg and back injuries and was hospitalized. Fall protection was not worn at the time of the incident.

Two employees were troubleshooting a pontoon boat motor. The motor began to run and the flywheel of its engine contacted an employee's right middle finger. The employee's fingertip was amputated.

An employee was placing fiber optic cable. A winch rope gained tension and one of the bull snaps failed, lacerating the employee's left palm and fracturing the employee's left little finger.

An employee working on a utility pole fell approximately 13 feet to the ground below, fracturing the left leg.

An employee was making modifications to an electrical panel when an arc flash occurred. The employee suffered burns to multiple parts of the body.

An employee was installing a ground wire to a power transmission pole. The ground wire contacted an energized portion of a cut-out, causing an arc-flash. The employee was hospitalized with second degree burns to their chest and arms.

An employee was connecting a utility transformer for underground service to a home. The employee's impact drill went across two connection bars with 240 volts of potential, creating an arc flash. The employee sustained burns to the face and eyes due to the arc flash and molten aluminum.

On December 15, 2023, at 9:15 AM, an employee was changing 60-amp fuses in a 480-volt panel when an arc flash occurred. The employee was hospitalized with burns to both hands.

An employee had just turned off breakers and was loosening wires on panels when they were shocked by 480 volts of electricity.

An employee was directing trucks as they entered and left a highway work zone. A vehicle struck them, resulting in multiple fractures and other injuries. The employee was hospitalized.

An employee was assisting the crew with patching and restoring a roadway after the installation of a sewer line. He was helping place and level the blacktop/backfill material over the trench area to bring the road surface back to proper grade. The employee was walking between a forward-moving dump truck and a dirt pile when his right foot was run over by the truck s wheel, causing him to fall. The employee sustained injury to his foot.

An employee was rigging I-beams. An I-beam slid off the stack of I-beams and fractured the employee's leg.

An employee was operating a skid steer with a bucket attachment at a demolition site. While driving it to the rear of the property to park it, the employee came into contact with a live electrical transformer unit that was located outside of the facility. The employee sustained electrical burns on his hands extending up to his elbows and a fractured ankle.

An employee was installing a door on a semi-trailer. They were using a forklift to lift the door to the height of the trailer when the door became jammed between the forklift mast and the hinge on the trailer. When the employee went to dislodge the door from the mast, the door fell and crushed their foot. Their big toe was amputated. The employee was hospitalized and their big toe was surgically reattached. The employee's foot and other toes also required surgery.

An employee was operating an ironworker (steel punching/shearing) machine. A piece of the tooling broke off and struck the employee's neck; a fragment was lodged in his neck. The employee was hospitalized and required surgery.

On October 25, 2025, an employee was stringing up a new reel of tire tread on a machine. The employee pulled a 6-inch tail and proceeded to spool up the liner. As the machine was jogged to begin the liner wrapping process, the liner caught the employee's glove and pulled their right arm into the liner, causing a fracture to the arm.

An employee was doing a cable change on top of an electric overhead traveling (EOT) crane. They were positioned between the cable drum and the drive shaft. While rotating the cable drum, the employee reached for the new cable that was to be installed. The grease fitting on the drive shaft caught their fall harness and pulled them underneath the drive shaft. The employee was pinned between the drive shaft and two pieces of angle steel, resulting in a fracture to their left hip.

An employee was helping two other employees to push a pallet of tile on a loading dock. He suffered a broken fibula and was hospitalized.

On October 5, 2025, an employee was pulling a pressure washer hose when it it disconnected from the cooker. The employee was struck by jets of high-pressure water, resulting in lacerations to their left thigh requiring surgery. The employee was hospitalized.