105,313Records 71,083Employers 85,290Hospitalizations 27,770Amputations 2015-01-01 2025-10-31
Safety Incidents OSHA Severe Injury Reports · 2015–2025

Shawnee Milling Company

Caught in running equipment or machinery during maintenance, cleaning · Amputations

Federal OSHA recorded a severe workplace injury at Shawnee Milling Company, 201 S. Broadway Avenue, SHAWNEE, OKLAHOMA 74801 on — Amputations, affecting the finger(s), fingernail(s), n.e.c..

An employee was monitoring the air-lock device that is used to move flour product to a different area of the facility. The air-lock machine became choked with product. The employee unscrewed a section of the housing and proceeded to unclog the machine. The machine activated while his right hand was in the point of operation resulting in amputation of the index finger to the first knuckle and lacerations to the middle and ring fingers.

Amputation Finger(s), fingernail(s), n.e.c. Special process machinery, unspecified

Shawnee Milling Company

An employee was walking through a door when the door closed quickly and amputated their right middle fingertip.

Shawnee Milling Company

An employee was doing electrical preventative maintenance on a motor control center. As he was about to tighten a metal screw with a metal screwdriver, he came into contact with the metal frame of the disconnect. The resulting arc flash caused second-degree burns to his right hand and face, as well as eye irritation.

Shawnee Milling Company

An employee was starting equipment with rollers that normally rotated in a outward motion to move stock away from the rollers, but had become a pinch point after maintenance. When the employee reached for stock, their left middle, ring, and little fingers got caught in the pinch point, resulting in amputations to the first knuckle.

SHAWNEE MILLING COMPANY

At the feed mill, an employee was wrapping red duct tape around a metal trough. His left index fingertip went inside the trough housing through an unseen hole in the metal. The conveyor screw inside the trough caused a partial amputation of the left index fingertip.

View Shawnee Milling Company's full OSHA safety record →

DGS Import, LLC

An employee was changing a saw blade when the saw machine activated. The employee's left ring and little fingers were amputated.

Millennium Mat Company

An employee was clearing a jam from the label cutting machine when their left middle finger was partially amputated.

Bauer Foundation Corp.

Two employees were repairing the hydraulic engagement pins on a rented front-end wheel loader. The machine controls were activated to move the attachment pins and an employee's finger was caught between the pins and the bushings. Their right index finger was partially amputated.

Guggisberg Cheese, Inc.

An employee was cleaning the conveyor on a piece of equipment when they slipped and their right hand was pulled into the chain sprocket. The employee's fifth fingertip was amputated.

Alsco Inc.

An employee was throwing blankets onto a blanket folding and stacking machine. A blanket got stuck in the machine and she attempted to remove it when the machine contacted her right little finger, resulting in a fingertip amputation.

Ardent Mills

An employee was walking into the motor control center (MCC) room when his right ring finger was caught in the hinge of a doorway. He sustained an open phalanx fracture, which resulted in a partial amputation above the first knuckle.

Mennel Milling Company

An employee was checking a flour roll stand for a blockage. The employee's right hand was caught in an ingoing nip point on the machine, causing partial amputations to the thumb and middle, ring, and little fingers.

Good Harvest Grain

An employee was working on a degerminator, which had been lifted by a crane. The machine fell onto the employee's arm and broke it.

Masa Milling, Inc.

An employee was climbing an A-frame ladder to adjust an exhaust pipe on the wall to let the heat out. The employee fell 4-5 feet and injured his right tibia and ankle.

Rae Corporation

An employee was helping to move a 1,300-pound coil on a cart. The steel caster hit a crack in the concrete, the weld holding the caster onto the cart broke, and the coil and cart tipped over onto the employee. He was hospitalized with a laceration on his forehead and a pelvic fracture on his right side.

Meeco Sullivan

An employee was cutting a piece of metal rod with a metal cutting machine. His right middle finger became caught between the rod and the machine's table. The employee's fingertip was partially amputated.

Edward Jones Investments

An employee was working at her desk. She went to stand up and fell to the floor beside the desk. The employee sustained a hip displacement and required surgery.

Burgess Manufacturing of Oklahoma Inc.

An employee was processing wood boards at a chop saw when the saw malfunctioned and the blade cut her left hand and fingers. She was hospitalized and her little finger was surgically amputated.