Welspun Tubular LLC

An employee was working in the pallet yard stacking lumber when their left index finger was crushed between two railroad ties, resulting in an amputation.

On December 4, 2023, at 12:30 PM, an employee was grinding a pipe. The stops on the skid failed and a pipe rolled backward onto the employee. The employee was hospitalized with bruising and contusions of the right leg.

An employee had just finished inspecting a steel pipe and rolled it forward to begin inspecting the next pipe. The pipe rolled back and caught his finger between both pipes, resulting in a crush injury to the fingertip that required medical amputation.

An employee was inspecting piping when the guarding of the pressure mat or safety door malfunctioned, causing the pipe from behind to move forward. The employee was caught between both pipes and the conveyor, resulting in a left leg amputation.

An employee was working at a grinder when pipes began coming off too fast. As the employee went to stop the pipes with the f-bar, their fingers became caught between the bar and a pipe. The employee sustained left middle and ring fingertip amputations.

A crew was pulling a 4-inch plastic gas pipe off a reel and straightening it for installation. The injured employee stepped up on the trailer to cut the last band holding the pipe in the coil on the reel. As he turned to step off the trailer, the end of the pipe rotated and sprung out of the cage surrounding the coil, striking the employee on the side of the head and knocking him off of the trailer into the roadway. The employee suffered head trauma that required hospitalization.

An employee and a co-worker were performing a pick inside a clear well. They rigged the skid pan that was full of broken concrete. When lifting, the load began to swing toward a wall. The employee tried to stop the skid pan from swinging and was struck by the pan, resulting in fractures to their left hip and wrist.

The employee had just completed refueling a lattice crane that was breaking up material and was winding the fuel hose back into the fuel truck when he was struck by the catwalk/stairs of the crane. The employee was hospitalized with a laceration to his backside, possible internal bleeding, and a broken hip.

An employee was fusing 10-inch black rubber utility pipes together using a pipe fusion machine and could not get the pipes to set correctly. The employee used a nylon strap attached to an excavator to lift one side of a pipe off a steel plate. As his hand was between two pipes, the pipes came back together, partially amputating two of his fingers.

An employee was lifting four bags of a lime blend weighing approximately 10,000 pounds using a crane. The load swung and pinned the employee against a structural I-beam, resulting in fractures to the hip and pelvis.

An employee fell onto a hot billet and suffered a burn to the left leg. The employee was hospitalized.

An employee was cutting wooden boards using a table saw when the glove on his left hand was caught by the blade, resulting in a partial fingertip amputation.

An employee was placing a board on top of a bundle of steel tubing. A crane was moving a bundle of steel that struck the employee and caught them against another bundle of steel tubing. The employee sustained a crushing injury and hematoma to the right upper leg.

A crane was hoisting a pipe. An employee was adjusting twisted lifting chains on the end of the pipe when the pipe was raised, causing the employee's hands to be caught between the chains and the pipe. The employee suffered injuries to the left index finger, left ring finger, right ring finger, and right index finger; the right index fingertip was amputated without bone loss.

During a routine inspection, an employee placed their hand on a pipe to check a weld. The pipe clamp activated, closed on the pipe, and trapped the employee's right middle finger, resulting in a partial amputation and fracture to the fingertip as well as a laceration to the ring finger.

An employee was operating an ironworker (steel punching/shearing) machine. A piece of the tooling broke off and struck the employee's neck; a fragment was lodged in his neck. The employee was hospitalized and required surgery.

On October 25, 2025, an employee was stringing up a new reel of tire tread on a machine. The employee pulled a 6-inch tail and proceeded to spool up the liner. As the machine was jogged to begin the liner wrapping process, the liner caught the employee's glove and pulled their right arm into the liner, causing a fracture to the arm.

An employee was doing a cable change on top of an electric overhead traveling (EOT) crane. They were positioned between the cable drum and the drive shaft. While rotating the cable drum, the employee reached for the new cable that was to be installed. The grease fitting on the drive shaft caught their fall harness and pulled them underneath the drive shaft. The employee was pinned between the drive shaft and two pieces of angle steel, resulting in a fracture to their left hip.

An employee was helping two other employees to push a pallet of tile on a loading dock. He suffered a broken fibula and was hospitalized.

On October 5, 2025, an employee was pulling a pressure washer hose when it it disconnected from the cooker. The employee was struck by jets of high-pressure water, resulting in lacerations to their left thigh requiring surgery. The employee was hospitalized.