Master-Halco, Inc.

An employee was inside a metal container from which temporary panels (sitting on pallets in the container) were being pulled. The employee was holding on to the side of the panels to stabilize them as they were lifted by a forklift. The panels started to tilt and then fell onto his left leg. He suffered a broken femur and was hospitalized, requiring surgery.

An employee was fixing a jam in the wire extruding machine and caught the tip of their finger between the drum and roller on the wire roll up. The employee sustained a right ring fingertip amputation. The machine was not locked out/tagged out at the time.

An employee was taking down warehouse racking when a piece of the racking fell down and amputated the tip of the employee's index finger.

An employee was clearing a jam in a rinse tank in a galvanizing-after-weaving department. The employee slipped and fell into a hot galvanizing tank next to the rinse tank. The employee suffered burns to the sole of a foot and the lower leg.

An employee was spooling wire coming off a wire draw machine when the end of a piece of fence wire struck the employee's eye. The employee suffered an eye injury requiring stitches. Safety glasses were not worn at the time of the incident.

The injured employee was assisting five other employees with bracing a wall panel that was being stood up. Another employee slipped on frost on the floor surface. The employees went to evacuate the area in anticipation of the wall panel falling over. The injured employee went to jump through a window opening within the wall panel and their lower half was crushed by the falling wall panel. The employee sustained a fractured pelvis.

An employee was helping to move a 1,300-pound coil on a cart. The steel caster hit a crack in the concrete, the weld holding the caster onto the cart broke, and the coil and cart tipped over onto the employee. He was hospitalized with a laceration on his forehead and a pelvic fracture on his right side.

An employee was attempting to lift a steel beam from a horizontal, stacked position to a vertical position using a crane. They had placed two hooks on the east side of the beam on the flange. As the employee was hoisting the crane, the beam began to shift and pulled the employee forward onto the stack. When the material shifted, the hooks released and the material fell, pinning the employee between the two beams. The employee was hospitalized with soft tissue contusions on their proximal right thigh and interior left thigh.

An employee was moving a tensile strength test device with a dolly. The device fell from the dolly onto the employee's right leg, causing a compound fracture.

An employee was rigging I-beams. An I-beam slid off the stack of I-beams and fractured the employee's leg.

An employee was driving a powered industrial truck (PIT) carrying a nesting sheave on the back counterweight of the PIT. He was holding the sheave when the PIT struck a pothole in the floor, causing the sheave to roll forward and crush his right index fingertip against the back of the PIT seat frame. The employee's fingertip was amputated, requiring hospitalization and surgery.

An employee was building slings. They were placing wire rope in a pneumatic vise when their right index finger was caught between the vise and the wire rope, resulting in a fracture that required hospitalization and surgery.

On September 15, 2025, an employee was working on an auto-welder when the guard closed on their left ring finger, resulting in a fingertip amputation.

At about 7:15 a.m. on August 28, 2025, an employee was using a construction compactor to stabilize the dirt of a dam that had just been built. The dirt gave way underneath the compactor, which tipped on its left side. The employee fell out and was crushed and pinned between the compactor and the dirt. He was hospitalized, having suffered a broken sternum and broken ribs on both sides, as well as a laceration to the left leg by the ankle joint.

A temporary employee was stripping wire for scrap when the machine crushed their left thumb and little finger.

An employee was operating an ironworker (steel punching/shearing) machine. A piece of the tooling broke off and struck the employee's neck; a fragment was lodged in his neck. The employee was hospitalized and required surgery.

On October 25, 2025, an employee was stringing up a new reel of tire tread on a machine. The employee pulled a 6-inch tail and proceeded to spool up the liner. As the machine was jogged to begin the liner wrapping process, the liner caught the employee's glove and pulled their right arm into the liner, causing a fracture to the arm.

An employee was doing a cable change on top of an electric overhead traveling (EOT) crane. They were positioned between the cable drum and the drive shaft. While rotating the cable drum, the employee reached for the new cable that was to be installed. The grease fitting on the drive shaft caught their fall harness and pulled them underneath the drive shaft. The employee was pinned between the drive shaft and two pieces of angle steel, resulting in a fracture to their left hip.

An employee was helping two other employees to push a pallet of tile on a loading dock. He suffered a broken fibula and was hospitalized.

On October 5, 2025, an employee was pulling a pressure washer hose when it it disconnected from the cooker. The employee was struck by jets of high-pressure water, resulting in lacerations to their left thigh requiring surgery. The employee was hospitalized.