Skyline Homes

An employee was cutting metal straps around a bundle of lumber. When they cut the last strap, the lumber fell off the forks of a forklift onto the employee's left foot, fracturing it.

An employee was picking up a spray gun to spray ceiling texture. The gun injected sheet rock material into the employee's right ring finger, causing an infection.

An employee was bending over to inspect a modular home and suffered a lower back sprain.

The injured employee was assisting five other employees with bracing a wall panel that was being stood up. Another employee slipped on frost on the floor surface. The employees went to evacuate the area in anticipation of the wall panel falling over. The injured employee went to jump through a window opening within the wall panel and their lower half was crushed by the falling wall panel. The employee sustained a fractured pelvis.

An employee was helping to move a 1,300-pound coil on a cart. The steel caster hit a crack in the concrete, the weld holding the caster onto the cart broke, and the coil and cart tipped over onto the employee. He was hospitalized with a laceration on his forehead and a pelvic fracture on his right side.

An employee was attempting to lift a steel beam from a horizontal, stacked position to a vertical position using a crane. They had placed two hooks on the east side of the beam on the flange. As the employee was hoisting the crane, the beam began to shift and pulled the employee forward onto the stack. When the material shifted, the hooks released and the material fell, pinning the employee between the two beams. The employee was hospitalized with soft tissue contusions on their proximal right thigh and interior left thigh.

An employee was moving a tensile strength test device with a dolly. The device fell from the dolly onto the employee's right leg, causing a compound fracture.

An employee was rigging I-beams. An I-beam slid off the stack of I-beams and fractured the employee's leg.

On September 5, 2025, an employee was installing gang plates on a structure when the side walls fell and hit her head. She then fell onto her back and the side wall pressed her to the ground, resulting in hospitalization due to an ilium fracture and a transverse process fracture on the right side.

An employee was blowing cellulose insulation into the open attic area of a manufactured home. While the employee was holding the insulation hose, it caught on the guardrail of the catwalk/suspended walkway leading into the attic. The tugging motion caused the employee to lose their footing and step onto the sheetrock ceiling. The employee fell through the ceiling to the ground about 8 feet below and suffered a broken lower left leg. The employee was hospitalized.

An employee was going between a ladder and a wall to repair a wall in the utility room. A brad-nailing gun was hanging on a piece of wood on the side of the ladder. The employee contacted the brad nailer and the trigger was pushed into the wooden piece. The brad-nailing gun actuated and shot a 2-inch brad into the employee's abdomen.

An employee was on a scaffold caulking and painting a manufactured home. She fell off the scaffold an estimated 6 to 8 feet, landing on the concrete floor. The employee suffered upper body injuries and was hospitalized.

An employee was going up a ladder from the first level roof to the second level roof. The ladder slipped and the employee fell approximately 8 to 10 feet to the surface on the first level. The employee sustained fractures to three ribs and bruises on their arms and hands.

An employee was working to remove a product blockage from a piece of equipment. The employee was struck by a metal bar near the deck of the pin mixer equipment and sustained blunt force trauma to the torso.

An employee was moving a rack onto a lower conveyor in the south heat treat area when their finger got caught between the part tray and the rollers, resulting in a fingertip fracture and amputation.

An employee was climbing a ladder to get on top of the breakroom. The ladder slipped, causing him to fall to the ground. The employee sustained fractures to his upper back, left foot, and ankle.

Two employees were removing a circuit breaker. The injured employee was using wrenches in the removal process. One of the wrenches contacted an adjacent door, resulting in an arc flash. The employee suffered burns to their neck, face, and ear, as well as momentary vision loss due to the flash.

An employee bent over to pick up a rubber mat from the ground. When he grabbed the corner of the mat, a rattlesnake hidden under it bit his left middle finger near the first knuckle. He was hospitalized.