Canton Drop Forge, INC.

An employee used the emergency stop to turn off the trim press. Hydraulic pressure released out of the cylinder, allowing the press to come down onto the employee's hand and amputate two fingers.

An employee was adjusting die liners in a forging hammer. The hammer engaged, and its key struck the employee's right arm, causing a compound fracture.

An employee was removing flash from a forged product using a long rod. The forge operator did not see the wand while it was within the press, cycled the hammer, and struck the wand. The wand then flew upwards, striking the employee in the right side of his face and resulting in a fractured jaw and cheek bone. The employee fell backwards and struck his head, resulting in a skull fracture.

An employee was placing a steel jamb near the opening of a rotary forging furnace and was struck by the steel jamb when it fell causing a contusion injury to the right calf.

On 1/19/2017, at approximately 1830, an employee was attempting to remove a die key from a steam-powered forging hammer when his leg became caught and injured between the key knocker ram and the hammer.

An employee was operating an ironworker (steel punching/shearing) machine. A piece of the tooling broke off and struck the employee's neck; a fragment was lodged in his neck. The employee was hospitalized and required surgery.

A service crew was pulling a pump and motor from a well. After breaking a joint of pipe loose from another joint, an employee grabbed the chain tongs to prevent the pipe from spinning in the well, so the crew could continue taking it apart. The bolt that attaches the chain to the handle of the chain tongs broke, causing the chain to swing around and strike the employee's lower right leg. The chain severely punctured his leg and fractured his tibia.

An employee was using a handheld grinder to cut a bolt. The grinding wheel broke apart and a fragment struck the employee s right hand, causing a laceration to the palm near the little finger.

An employee was operating a brake press when the top die broke, causing the bottom die to roll out and onto the employee's legs. Both of the employee's legs were crushed below the knee, and both legs were partially amputated. The employee's left leg was also fractured above the knee.

A pressurized aircraft nose landing gear strut assembly was being disassembled. The gland nut dislodged under pressure and made contact with an employee's left hand, breaking it.

An employee was riding on the side of a forklift. He stepped off the forklift and was struck by the back end of the forklift as it turned to the right. The forklift's back tire ran over his leg, resulting in an amputation. The employee was hospitalized.

An employee was loading a nozzle, weighing approximately 500 pounds, onto a positioner. The stainless steel nozzle slipped off the positioner and struck the employee's right leg. The employee's right tibia was fractured and their left knee was bruised.

An employee was preparing a hammer and dies for operation. The ram prop was inserted in the hammer to secure the ram. While the employee went to apply grease to the die shim in the hammer, the ram moved downward. The motion dislodged the prop, causing the ram to drop and crush the employee's right hand and forearm. The employee sustained amputations to their hand and arm and was hospitalized.

An employee was doing a tool changeover on a table mill and changing the mandrel. His hands were on both wrenches with his right thumb was between the two wrenches as he worked to unlock the mandrel. The wrenches came together, crushing his thumb. The employee was hospitalized with a partial amputation of the thumb.

An employee was helping to remove tooling that was stuck in a forging press (a full-revolution mechanical power press). The press cycled, resulting in partial amputations to two fingers on his left hand.

An employee was working to deliver mail to an apartment building. She was waiting for a customer to move, to obtain clearance to the mailboxes. The door swung inward and closed on her right little finger. The top half of her finger was surgically amputated.

An employee fell from a step ladder while reaching for a tie-off point. He impacted the ground, and landed on his bolt bag which contained tools. The employee was hospitalized with fractured ribs, and a lacerated spleen and kidney.

On October 30, 2025, an employee was working to adjust a stackable metal shipping container. As the container dropped into place, it caught the employee's hands in an area between the upper and lower cross-members. The employee suffered a laceration to the left ring finger that required stitches, bruising to the right ring finger, and fractures to the right middle finger that necessitated medical amputation of the fingertip.

An employee was moving a scissor lift through a doorway. The employee was pinned between the scissor lift and the doorframe, sustained a back injury, and was hospitalized.

An employee was setting up communication equipment for a meeting. They were walking and tripped over a speaker on the ground. The employee sustained a leg injury.