KAWNEER COMPANY, INC.

On May 5, 2025, an employee was loading large, fixed door panels inside a trailer to be delivered to the customer. While positioning a panel, it began to tip to the left and contacted the other panels that were in a row inside the trailer. This caused the 11 panels in the row to fall and pin the employee against the trailer wall. The employee was hospitalized with a laceration to the head and head trauma.

An employee was operating a forklift with a hopper, dumping aluminum extrusion scrap. The employee had driven into a trailer to dump a load of scrap, then left the forklift cab and released the dump on the hopper so the material could be dumped forward into the trailer. The hopper moved back toward the forklift and caught the employee's left ring finger against the forks. The finger was partially amputated.

Two employees were repositioning an extrusion press's tail stretcher. The head stretcher was moved closer to the tail stretcher while one employee's right hand was on the material flow table. His little finger was pinched between the metal and the table, suffering an amputation.

A temporary employee was teaching an employee how to clean rollers in the pouring and debridge area of the facility. When they were done cleaning the roller, the employee placed it back into the lathe and used a chuck key to tighten it into place. The temporary employee instructed the other employee to turn on the lathe. As the lathe was being turned on, the temporary employee saw the key was still in the chuck and went to remove it. The employee's finger got caught between the key and the guard resulting in amputation of the left index fingertip.

An employee was maneuvering a steel transport cart next to a similar steel transport cart when his left fifth digit was pinched between the two carts, causing a laceration, fracture, and dislocation to the distal phalange.

The injured employee was assisting in the disassembly phase after a radar array had been lowered and secured. The crew began removing load bearing pins from an overhead crane to free the radome. A load bearing pin was stuck. The injured employee went to remove the pin manually as a second team member applied pressure from the opposite side. The pin unexpectedly released and struck the injured employee s right thumb, resulting in partial amputation of the distal phalanx including an open distal phalanx fracture and nail bed laceration.

An employee was shoveling excess material (spillage) that consisted of dry mix, sand, aggregate and cement. As he was shoveling, some material blew back in his face and around his safety glasses. He got a piece of metal in his left eye that required surgery. The employee was hospitalized.

An employee was feeding boards into an edger. They fed a board in and then adjusted the blade for a second board that was wider. When they fed the second board into the edger, it hit the first board and kicked back, striking the employee in the chest. They sustained injuries including a spine fracture, an injured pancreas, as well as potential injuries to their spleen, liver, and intestine. The employee was hospitalized and required surgery.

An employee was helping an operator to pull a cable off a winch. The operator pulled in the line when it hooked some tree brush. The brush then whipped around and struck the employee's arm, resulting in a broken arm.

A co-worker was adjusting an overhead bracket with an impact wrench when the tool flew out of their hand and struck the injured employee in the face. The injured employee sustained an injury to their left eye.

On October 14, 2025, an employee was cutting lumber on an upcut saw. When he activated the saw to cut a short piece, the blade struck the tip of his right thumb, resulting in a partial amputation.

An employee was using a table saw to cut strips of plywood. The employee's left hand came into contact with the sawblade, which amputated the index and middle fingers as well as lacerating the hand. The employee was hospitalized, requiring surgery.

An employee was loading four sliding glass door panels into a truck. He was turning to get a cargo strap when the panels fell onto him and broke his neck.

An employee was using a table saw to cut a small bundle of vinyl material. The saw blade lacerated the employee's left index finger. The employee was hospitalized.

An employee had finished installing hurricane shutters on a customer's home and was putting his tools away and changing clothes. His hands began to cramp; he got out of his truck and collapsed on the road. He suffered an acute kidney injury and rhabdomyolysis caused by dehydration and heat illness.

An employee was operating an ironworker (steel punching/shearing) machine. A piece of the tooling broke off and struck the employee's neck; a fragment was lodged in his neck. The employee was hospitalized and required surgery.

On October 25, 2025, an employee was stringing up a new reel of tire tread on a machine. The employee pulled a 6-inch tail and proceeded to spool up the liner. As the machine was jogged to begin the liner wrapping process, the liner caught the employee's glove and pulled their right arm into the liner, causing a fracture to the arm.

An employee was doing a cable change on top of an electric overhead traveling (EOT) crane. They were positioned between the cable drum and the drive shaft. While rotating the cable drum, the employee reached for the new cable that was to be installed. The grease fitting on the drive shaft caught their fall harness and pulled them underneath the drive shaft. The employee was pinned between the drive shaft and two pieces of angle steel, resulting in a fracture to their left hip.

An employee was helping two other employees to push a pallet of tile on a loading dock. He suffered a broken fibula and was hospitalized.

On October 5, 2025, an employee was pulling a pressure washer hose when it it disconnected from the cooker. The employee was struck by jets of high-pressure water, resulting in lacerations to their left thigh requiring surgery. The employee was hospitalized.