Norfolk Iron & Metal

An employee was taping a roll of 22-gauge metal after rewinding the material on a leveler. The machine began operating and the employee's left hand got caught between the snubber and the material. Their ring, middle, and little fingers were fractured. The ring finger was crushed and the fingertip was amputated.

The injured employee was assisting five other employees with bracing a wall panel that was being stood up. Another employee slipped on frost on the floor surface. The employees went to evacuate the area in anticipation of the wall panel falling over. The injured employee went to jump through a window opening within the wall panel and their lower half was crushed by the falling wall panel. The employee sustained a fractured pelvis.

An employee was helping to move a 1,300-pound coil on a cart. The steel caster hit a crack in the concrete, the weld holding the caster onto the cart broke, and the coil and cart tipped over onto the employee. He was hospitalized with a laceration on his forehead and a pelvic fracture on his right side.

An employee was attempting to lift a steel beam from a horizontal, stacked position to a vertical position using a crane. They had placed two hooks on the east side of the beam on the flange. As the employee was hoisting the crane, the beam began to shift and pulled the employee forward onto the stack. When the material shifted, the hooks released and the material fell, pinning the employee between the two beams. The employee was hospitalized with soft tissue contusions on their proximal right thigh and interior left thigh.

An employee was moving a tensile strength test device with a dolly. The device fell from the dolly onto the employee's right leg, causing a compound fracture.

An employee was rigging I-beams. An I-beam slid off the stack of I-beams and fractured the employee's leg.

A load of steel angles was being lowered when the lifting chain hit the load, causing it to slide toward an employee. An angle slid and pinched the employee, catching both of their legs between the beams and an angle. The employee suffered two fractured legs.

An employee was on the deck of a trailer helping a customer unload tubes. The employee was working to place a cargo strap on the remaining tubes using a winch bar when it slipped off the tubing, causing him to lose his balance and fall headfirst onto the asphalt lot below. The employee suffered a contusion on his forehead, resulting in hospitalization.

An employee and a customer were unloading two rectangular tubes. The tubes were wrapped together. The plastic wrap was cut so that one tube could be picked up. As the employee was lifting the top tube, the other tube (still connected to the top tube) came down onto his hand and broke two of his fingers. He was hospitalized.

An employee was assisting as a forklift got pipe from a pipe rack. The employee was on one of the forklift's forks as it was raised to the top of the rack, a height of about 15 feet. He fell to the ground and suffered a dislocated and fractured right elbow.

On September 23, 2025, at approximately 7:43 p.m., an employee was using a knife to cut poly banding from a metal coil. The knife slipped, causing a laceration to the inside of their left arm at the elbow joint. The employee was hospitalized and required surgery to repair a damaged vein.

An employee was helping to move a 1,300-pound coil on a cart. The steel caster hit a crack in the concrete, the weld holding the caster onto the cart broke, and the coil and cart tipped over onto the employee. He was hospitalized with a laceration on his forehead and a pelvic fracture on his right side.

An employee was working in the food service warehouse when he experienced chest pain, difficulty breathing, and lost consciousness. The employee sustained carbon monoxide poisoning.

An employee was cutting a piece of metal rod with a metal cutting machine. His right middle finger became caught between the rod and the machine's table. The employee's fingertip was partially amputated.

An employee was working at her desk. She went to stand up and fell to the floor beside the desk. The employee sustained a hip displacement and required surgery.

An employee was processing wood boards at a chop saw when the saw malfunctioned and the blade cut her left hand and fingers. She was hospitalized and her little finger was surgically amputated.