Cleveland-Cliffs Inc

A train operator was transporting carts of molten iron from the blast furnace to oxygen furnaces. He was working to couple four carts to two other carts while going around a slight curve on the track. A hard coupling event occurred causing molten iron to splash out of the carts and onto the employee. The employee sustained first-degree burns to the face and knees.

An employee and co-worker were participating in a hands-on alignment training of a device that consisted of an electric drive motor, a belt, pulleys, a chain, and sprockets. The employee finished checking the tension and alignment on the training aid and prepared to energize the device s motor to spin the chain and check their work. The device activated causing the injured employee s right ring finger to become caught between the chain and sprocket. The employee suffered a fingertip injury resulting in amputation down to the first joint.

An employee was carrying out a shrink-wrapping task. The employee's right little finger was pinched between a skid runner and a driven conveyor roll, causing an amputation to the finger.

Two operator technicians were processing side trim coils on a repair line when scrap on the north side became jammed in the scrap chute. The employee stopped the line and went to clear the scrap buildup as the other employee jogged the machine to realign the scrap for the other employee to remove. The injured employee's left hand was then caught on the scrap chopper and his left index, middle, and ring fingers were crushed.

An employee was cutting a roll of steel from a slitter machine when their arm became caught in the machine, resulting in compression injuries to their arm and hand that required hospitalization.

An employee was operating a battery-powered broom to clean demolition debris off the top of the outermost bridge girder. The girder was approximately 11 feet above the demolition scaffold below. The employee fell approximately 8 feet to wind bracing below. The employee was hospitalized with a pelvis/tailbone fracture. Fall protection was in place at the time.

An employee was standing on the surface of a steel beam about two feet wide. He slipped and fell backward, landing on the concrete ground about 20 feet below. The employee sustained a broken pelvis.

An employee was cleaning out an inlet pipe in a stormwater structure. The employee stepped back, fell into the pipe, and landed on concrete 13 feet below, at the bottom of the structure. He suffered a broken back.

An employee was working on a platform, raised 6 to 8 feet in the air, to get something off a rack. The employee fell from the platform to the ground and sustained a head injury and injury to multiple body parts.

An employee was preparing to unjam an auger shaft while standing on a forklift-elevated, job-made platform. The employee's wrench slipped off the equipment, causing them to lose their balance and fall. The employee landed on the ground 14 feet below and suffered fractures to the orbital bone, left elbow, and lower back.

An employee used a crane to set down a bar. The bar measured 9 inches by 16 feet. The strap got stuck under the bar, and the employee asked another employee to jog the roll. The bar rolled and pinched the injured employee's left hand, resulting in a fingertip amputation.

An employee was loading a steel forming machine with steel to be processed. He went to move a cooling hose out of the way and his left thumb was crushed by the forming roller, resulting in injuries that required surgical amputation.

An employee was advancing a rail to line up for welding with a secondary rail on the weld line when his right middle and ring fingers were caught between the rails. The employee sustained an amputation to the top knuckle of the middle finger and a fracture to the ring finger. The machine was guarded at the time.

An employee was working near molten metal and experienced heat illness symptoms including cramps. The employee was hospitalized.

An employee was preparing bundles of 24-foot square metal tubing to be loaded onto a truck and cut the safety band for a bundle. While the employee was removing a piece of dunnage from a bundle, they bumped the bundle with their leg. The metal tubing then fell forward and struck the employee, causing a fractured left ankle.

An employee was working to deliver mail to an apartment building. She was waiting for a customer to move, to obtain clearance to the mailboxes. The door swung inward and closed on her right little finger. The top half of her finger was surgically amputated.

An employee fell from a step ladder while reaching for a tie-off point. He impacted the ground, and landed on his bolt bag which contained tools. The employee was hospitalized with fractured ribs, and a lacerated spleen and kidney.

On October 30, 2025, an employee was working to adjust a stackable metal shipping container. As the container dropped into place, it caught the employee's hands in an area between the upper and lower cross-members. The employee suffered a laceration to the left ring finger that required stitches, bruising to the right ring finger, and fractures to the right middle finger that necessitated medical amputation of the fingertip.

An employee was moving a scissor lift through a doorway. The employee was pinned between the scissor lift and the doorframe, sustained a back injury, and was hospitalized.

An employee was setting up communication equipment for a meeting. They were walking and tripped over a speaker on the ground. The employee sustained a leg injury.