Micro Plastics, Inc.

An employee was using his left hand to push an axle down the line on a raised track work area while holding the remaining axle back with his right hand. A finger on his right hand was caught between the rail and the dust guard of the axle, resulting in a fracture and a laceration.

An employee was moving metal out of a cart. He had removed one piece and was working to move another when the metal shifted. His right ring finger was crushed between the two pieces, and he suffered a partial amputation to the finger pad at the tip.

A load of steel angles was being lowered when the lifting chain hit the load, causing it to slide toward an employee. An angle slid and pinched the employee, catching both of their legs between the beams and an angle. The employee suffered two fractured legs.

Employees were replacing a 24" pig trap door. A strap was shackled on the pig trap door and connected to a forklift. Welders began to cut the door off. An employee was holding onto the door when the cut was finished. The door shifted and caught his fingers, resulting in a hand injury and amputation.

An employee used a crane to set down a bar. The bar measured 9 inches by 16 feet. The strap got stuck under the bar, and the employee asked another employee to jog the roll. The bar rolled and pinched the injured employee's left hand, resulting in a fingertip amputation.

A subcontracted engineer was advising maintenance how to make a modification to the embossing roll system on a new line. Maintenance was bringing the motor and gearbox down with a crane. The load shifted when it was a few inches from the ground. The engineer went to catch/maneuver the gearbox and the fingers on his left hand were crushed between the I-beam base of the gearbox and the concrete floor. A finger was amputated.

An employee was manually lifting a film roll when their right middle fingertip was pinched between the roll and a metal beam, resulting in a fingertip amputation.

At about 10:00 a.m. on July 13, 2025, an employee was cleaning the adhesive from running rollers using a rag soaked in cleaning solvent to prevent contamination. The rag was caught between two rollers and pulled the employee's right hand between the rollers. The employee sustained right hand crushing injuries, de-gloving injuries (palmer and dorsal sides), and fractures. The employee was hospitalized and required surgery. The machine was not locked out/tagged out at the time.

An employee working on a sheet line was removing masking from the underside of plastic sheeting that was being lifted by a vacuum lift. The plastic sheet measured 4 feet wide, 14 feet long, and approximately 1 inch thick, and it weighed approximately 300 pounds. The vacuum lost suction and dropped the plastic sheet onto the employee's arm, pinning it between two sheets and resulting in a broken right forearm.

An employee went to remove the air bar from a roll of plastic sheeting and needed to unjam a shaft that was stuck inside a metal core. He stood on one side of the shaft and core, and went to push/pull the shaft out of the core in order to free the core. The shaft became free all at once, pulling the core toward the employee; his fingers were pinched between the core and the shaft. His ring fingers on both hands sustained cuts and fractures and required stitches. His little fingertip was fractured and required surgical amputation.

An employee was operating an ironworker (steel punching/shearing) machine. A piece of the tooling broke off and struck the employee's neck; a fragment was lodged in his neck. The employee was hospitalized and required surgery.

On October 25, 2025, an employee was stringing up a new reel of tire tread on a machine. The employee pulled a 6-inch tail and proceeded to spool up the liner. As the machine was jogged to begin the liner wrapping process, the liner caught the employee's glove and pulled their right arm into the liner, causing a fracture to the arm.

An employee was doing a cable change on top of an electric overhead traveling (EOT) crane. They were positioned between the cable drum and the drive shaft. While rotating the cable drum, the employee reached for the new cable that was to be installed. The grease fitting on the drive shaft caught their fall harness and pulled them underneath the drive shaft. The employee was pinned between the drive shaft and two pieces of angle steel, resulting in a fracture to their left hip.

An employee was helping two other employees to push a pallet of tile on a loading dock. He suffered a broken fibula and was hospitalized.

On October 5, 2025, an employee was pulling a pressure washer hose when it it disconnected from the cooker. The employee was struck by jets of high-pressure water, resulting in lacerations to their left thigh requiring surgery. The employee was hospitalized.