Struck by running powered equipment n.e.c. · Cuts, lacerations, punctures without injury to internal structures
At a glance
Federal OSHA recorded a severe workplace injury
at MetalTek International, Inc., 905 East St. Paul Avenue, WAUKESHA, WISCONSIN 53188
on — Cuts, lacerations, punctures without injury to internal structures, affecting the Exterior and musculoskeletal structures of the back unspecified.
Final narrative
An employee was turning off a gas valve when he bumped into a die brush and struck the spinning die. The die pin struck him on the back, resulting in contusions, abrasions, and a severe laceration to his back that required hospitalization and surgery.
Hospitalized Exterior and musculoskeletal structures of the back unspecified Metal, woodworking, and special material machinery unspecified
More severe injuries at MetalTek International, Inc.
On October 9, 2024, an employee was repositioning the end of a metal casting that was not attached to the hoist. The employee's left ring finger was crushed between the part and the work table, resulting in the amputation of their left ring fingertip.
An employee dropped a hot ARC rod onto the sand floor. The rod contacted his boot, burned through the leather, and contacted his left foot. He suffered burns to his foot and toes, which required surgery.
An employee was changing out an empty tote of wash for a full tote in a foundry. The mixer/frame fell and struck the employee's left arm, causing a compound fracture.
After cutting a slab of beef short ribs, an employee turned to grab the pieces he had cut and his right hand contacted the saw blade. The employee sustained an amputation to his right index finger.
An employee was using a vertical band saw to cut a thick piece of rubber material. While being cut, the material shifted, causing the employee s right hand to contact the moving blade. The employee's thumb was amputated below the knuckle. The employee was hospitalized, undergoing surgery.
More severe injuries in this industry (NAICS 331513)
An employee was unloading metal from two drums on a pallet. The employee removed the lid from the second drum and the drum fell over onto his ankle. The employee sustained a fractured ankle.
An employee was working with team members on the pouring line, casting a sand mold. Molten metal entered the employee's personal protection suit and severely burned his left leg, calf, and ankle.
An employee was jointing a board with a jointer. The board jumped when it came into contact with the jointer's cutter head, and the jolt caused the employee's left hand to slide between the board and the guard and come into contact with the cutter head. He suffered lacerations/partial amputations to the middle, ring, and index fingers.
At 11:45 a.m. on June 13, 2025, an employee of Staley Steel, LLC, was performing preventive maintenance on an overhead crane. While he was holding a grease gun hose and nozzle, he contacted electrical components inside an electrical box. He suffered a first-degree electrical burn on the palm of the left hand, as well as pain up his left arm to the shoulder, and was hospitalized.
The injured employee was assisting five other employees with bracing a wall panel that was being stood up. Another employee slipped on frost on the floor surface. The employees went to evacuate the area in anticipation of the wall panel falling over. The injured employee went to jump through a window opening within the wall panel and their lower half was crushed by the falling wall panel. The employee sustained a fractured pelvis.
An employee was using a vertical band saw to cut a thick piece of rubber material. While being cut, the material shifted, causing the employee s right hand to contact the moving blade. The employee's thumb was amputated below the knuckle. The employee was hospitalized, undergoing surgery.
A production sanitation employee was pre-rinsing an incline conveyor and noticed cheese stuck between the belt idler. The employee went to remove the cheese and their glove got caught and pulled their left forearm into the conveyor. The employee's arm was fractured. The machine was not locked out/tagged out at the time.
An employee was on a ladder, taking measurements for a new gutter installation. The ladder slipped out from under him and both he and the ladder fell to the ground. He was hospitalized with seven broken ribs and a broken clavicle.
An employee was unloading a truck for a delivery job. While moving boxes in the truck, the employee tripped over a pallet and fell out of the truck to the ground, resulting in four broken ribs.