Northrop Grumman Corporation

On August 19, 2025, at 6:30 a.m., an employee sat in the rear bench seat of a golf cart ahead of being driven to a parking lot. When the golf cart began to move, he fell off the cart and onto the ground, resulting in a fractured right hip.

An employee was standing on the driver's side deck of a moving golf cart. When it turned, they fell to the ground and sustained a dislocated right ankle and a fractured fifth toe.

An employee was installing a duct through a scaffold hatch. The hatch fell closed, landing on his left little finger and amputating the tip.

An employee fell from an industrial stairway, landing on the floor about 4 feet below. He suffered a concussion and head laceration, a broken finger on the left hand, and contusions to the right shoulder, right-side ribs, and abdomen.

On April 15, 2020, an aircraft electrician was retrieving a tool that fell through the grated cover of a two-foot utility trench. While lifting the grated trench cover, he lost his grip. The trench cover fell and his middle finger was caught between the cover and the floor. He sustained an amputation without bone loss to his right middle fingertip.

After cutting a slab of beef short ribs, an employee turned to grab the pieces he had cut and his right hand contacted the saw blade. The employee sustained an amputation to his right index finger.

An employee was cutting cabinet trim using a table saw when four fingers on his left hand were severed, resulting in hospitalization and amputation.

An employee was using a meat saw to slice pork when the blade amputated their right little fingertip.

An employee was struck by a plasma cutter and suffered a broken left tibia and fibula. The employee was hospitalized.

An employee was using a vertical band saw to cut a thick piece of rubber material. While being cut, the material shifted, causing the employee s right hand to contact the moving blade. The employee's thumb was amputated below the knuckle. The employee was hospitalized, undergoing surgery.

A pressurized aircraft nose landing gear strut assembly was being disassembled. The gland nut dislodged under pressure and made contact with an employee's left hand, breaking it.

A metal tooling base was being moved by a forklift when the load shifted. An employee who was assisting went to stabilize the load and prevent it from sliding off the forks. The C-channel of the base crushed the employee's left hand against the concrete ground, resulting in the amputation of their third and fourth fingers.

An employee was working on a tool platform (47.5" tall) and was transitioning around to the other side when they lost balance and fell to the concrete floor. The employee was hospitalized with fractures to seven ribs and their elbow.

On August 19, 2025, at 6:30 a.m., an employee sat in the rear bench seat of a golf cart ahead of being driven to a parking lot. When the golf cart began to move, he fell off the cart and onto the ground, resulting in a fractured right hip.

An employee was preparing the wing of an aircraft for stripping work and was standing on a four-foot step stand. As the employee was walking on the top platform of the stand, they stepped off the end of the stand and fell to the ground. The employee sustained fractures to their left elbow and left hip.

The injured employee was assisting a Department of Homeland Security (DHS) enforcement operation. During an apprehension, officers returned fire at a subject and struck the employee with a bullet. The employee sustained a gunshot wound to their right hand.

The injured employee was assisting in the disassembly phase after a radar array had been lowered and secured. The crew began removing load bearing pins from an overhead crane to free the radome. A load bearing pin was stuck. The injured employee went to remove the pin manually as a second team member applied pressure from the opposite side. The pin unexpectedly released and struck the injured employee s right thumb, resulting in partial amputation of the distal phalanx including an open distal phalanx fracture and nail bed laceration.

An employee was working on an electrical panel in a mechanical room when an arc flash occurred. The employee suffered burns.

At about 3:10 p.m. on October 3, 2025, an employee was inspecting a car. Two dogs that had been in another car were leashed and tethered to a bollard. As the employee inspected the first car along with a narcotics detection dog, one of the other dogs came loose and attacked the narcotics dog. The employee was separating the dogs when the other dog bit his left ring finger. The last joint of the finger was injured and part of it was bitten off.

An employee was preparing a bundle of green onions for chopping. While holding the bundle in his left hand, he made his first cut using a 9-inch kitchen knife held in his right hand. The knife contacted the tip of his left thumb, resulting in an amputation of approximately 0.5 inches of the thumb that required hospitalization.