Hammond Lumber Company

An employee was unlocking the main gate to prepare for sanding and plowing. He slipped on a patch of black ice on the driveway, fell, and hit his head, resulting in a skull fracture.

An employee was climbing a step ladder while carrying a 3-foot piece of conduit. As he went to reposition his feet on the ladder by pivoting, he slipped and fell from the third rung of a 6-foot ladder. The employee sustained fractures to the left femur, right elbow, and right ring finger.

An employee was descending a 4-step maintenance stand when she missed the bottom step and fell to the hangar floor. The employee suffered a left hip fracture.

An employee stopped a belt and was going to check it for missing packages. She fell backward 3-4 feet from an elevated platform and sustained a broken right arm.

An employee had just finished a routine concrete pour and was ascending the ladder to clean the concrete mixer truck. The employee lost their grip and fell approximately 2-3 feet, contacting the truck's bumper. The employee suffered rib fractures and a punctured lung.

An employee was performing duties as an expeditor. After opening the dock door, the employee scanned the barcode on the door of the truck and placed one foot on the truck and one foot on the dock. The truck drove out of the stall, causing the employee to fall 4 feet off the dock onto the concrete. The employee sustained fractures to the right side of the pelvis, elbow, and a left ring fingertip as well as injuries to the right wrist and bruising to the back and stomach.

An employee was unloading freight from a truck when a stack of doors fell over and knocked the employee to the ground. The employee sustained a fractured femur.

An employee was performing rebar fabrication using a bending machine. The employee's glove became caught in the area where the rebar bend overlaps onto itself. The subsequent bending/cutting caused the two overlapping portions to squeeze together and amputate approximately 1/4" of his left index fingertip.

An employee was building wood detail blocking and a wood member needed to be resized. The employee took the wood member to the table saw and set the fence to the correct size. The employee pressed down on the board to control it when his left little finger contacted the running blade, resulting in an amputation.

An employee was clearing a pipe along a culvert using a motorized plumbing machine. The end of the machine got tangled and stuck in long grass and other debris. The employee went to lift the end of the machine out of the grass and clear the blockage when his hand was pulled into the machine, resulting in a partial amputation and open fracture of his left distal phalanx.

An employee was operating a router when it cut his right little finger, causing an amputation through the bone.

A crew was installing drilled micropiles alongside an outdoor covered deck foundation. The injured employee was working the front of the drill when a loose section of casing dropped onto the tip of a rig wrench and pulled the wrench down to an embedded casing. The employee's left little finger was caught between the rig wrench and the embedded casing and was amputated above the top knuckle.

Two employees were working to change a tire on a mobile slasher saw. The slasher weighs around 2,000 pounds and is towed. Employee 2 was lifting the saw while the injured employee was placing a block of wood under the frame for support. The slasher then lowered onto the block and the injured employee's left thumb was crushed between the slasher frame and the wood block, leading to an amputation at the first knuckle.

An employee was using a metal shear when it amputated the tip of his right index finger.

An employee was using a crane to move a 44-foot, 3,343-pound I-beam. As the beam was moving west, it straightened out (north to south), beginning to swing south toward the northwest corner of a building. The crane then sent the beam southward, directly toward the corner of the building. The beam caught the tips of the employee's left index, middle, and ring fingers against the building. The last joints of the middle and ring fingers were amputated, and the last joint of the index finger was partially crushed.

An employee was standing on a step stool, removing the nuts and bolts from the frame of a solar panel that was being replaced. The employee's cheek made contact with a connector with damaged insulation. The employee was shocked, briefly lost consciousness, and fell to the ground, suffering an injury to the left shoulder.