Faddis Concrete Products

An employee was attempting to close a bay door when it struck them in the back of the head and neck before coming to rest on their right leg. The employee suffered lumbar fractures and a displaced ankle fracture.

An employee and a co-worker were preparing to remove a load of mesh from a flatbed. After releasing the ratchet strap that was being used to secure the mesh, the tension on the strap caused the mesh to shift and fall toward the employee. The employee was pushed into a panel behind him, resulting in a fractured left index finger, C5 and C7 spinal fractures, and possible nerve damage.

An employee was scraping concrete from a form. As he tried to lift a panel with an overhead crane, his finger was caught between the panel and the chain of the lift. The finger was crushed and the fingertip was fractured. The fingertip was later medically amputated.

A temporary employee utilized an overhead crane to move a concrete panel from one area to another. The panel started moving towards a post. The employee put his hand on the concrete panel to stop it before hitting the post, but his left hand was caught between the panel and the post. The employee sustained a crushing injury to the left hand and was hospitalized for surgery.

Three concrete panels were placed on dunnage, approximately 6" off the ground in the batch end area of the plant. The dunnage was perpendicular to the panels and approximately 3 feet from each end of the panel. These panels were spaced about 3 to 4 feet apart and were free standing on the dunnage. At 6:40 p.m., an employee was picking up foam pieces in the same area and placing them into a 5-gallon bucket. He bent down to pick up an item about midway down the panel when the second panel from the bay door started to tip as the employee stood up. The panel came down and hit the employee about waist level (front side) and pushed him back into the third panel (closest to bay door). Both panels fell towards the south end of the building and the second panel ended up on top of the employee's right leg. The dunnage acted as a buffer to keep his leg from being fully crushed. He was hospitalized with a broken right tibia and torn right knee ligaments.

An employee was using a two-step step stool to stock product on shelves. The stool collapsed and the employee fell to the ground sustaining a fractured femur.

An employee was walking around and closing up the office for the day. As he was on a table closing the blinds, the table collapsed, causing the employee to fall. He sustained a left kneecap fracture.

Employees were demobilizing a microtunneling operation from inside of a 42-foot shaft. They were standing on a 3-foot high pump stand to disconnect the pump when the pump dropped, and the stand gave way. This caused the employees to slide and fall to the ground. The injured employee fell on his left side, landing on an oil can with his co-worker landing on top of him. The injured employee was hospitalized for a rib fracture.

An employee was on a wood platform surrounding a containment wall to work on a transformer. While inspecting the equipment, the wood platform collapsed, causing the employee to fall approximately 4 feet. The employee's shoulder was fractured and required surgery.

An employee was standing on a baker's scaffold approximately 3 feet above finished floor to install equipment. While taking measurements, the locking pins came out on one end of the scaffold, causing the scaffold to collapse. The employee fell 3 feet and sustained a left ankle injury.

An employee was walking through the garage and stepped on a mechanic's creeper. His feet went out from under him and he fell, sustaining a fractured right femur.

An employee was exiting a loader and coming down the ladder. His hand slipped off the railing and he fell backward onto sandy ground, landing on his side. The employee was hospitalized with a fractured pelvis and a rotator cuff tear.

A concrete mixer truck driver was walking up the stairs of the slump rack. They fell from the slump rack platform and landed on the ground in the wash-out area. The employee sustained fractures to their left scapula and lower back vertebrae.

An employee backed their concrete truck into place to begin unloading it into a concrete pump unit. He exited the vehicle, and went to the rear to unload. When he began unloading, the truck rolled backward and pinned him against the pump unit. The employee sustained fractures to their pelvis, both femurs, both tibias and fibulas, and their left ankle.

A mechanic was changing out an air spring on a concrete mixer truck cab. The air spring was receiving higher air pressure than it was designed to use, because of a faulty level check valve. This increased pressure caused the air spring to burst. Its top portion separated and struck the employee's left forearm, causing a laceration and fracture. The employee was hospitalized, requiring surgery.

An employee was closing a door when the door closed on their right index finger, resulting in a fingertip amputation.

An employee was walking into the motor control center (MCC) room when his right ring finger was caught in the hinge of a doorway. He sustained an open phalanx fracture, which resulted in a partial amputation above the first knuckle.

An employee was changing the spacing on a telehandler's forks. A fork slipped, and the employee's left index finger was caught between it and the mast. The fingertip was medically amputated at the first knuckle.

An employee was pulling down a broken skid with a forklift. When the employee backed up the forklift to get the forks out of the skid he pulled down, he contacted the forks of another parked forklift, fracturing both of his legs. He was hospitalized.

An employee was carrying cups back to the kitchen when her foot got caught on a cart and she fell face-first. During the fall, a piece of glass from a cup cut the inside of her mouth, severing an artery. She also sustained a laceration on her lower lip. The employee was hospitalized.