Nemak Corporation

An employee was dumping a tray of water when her right hand struck the side of a machine. She suffered a contusion that required surgery. The machine was unguarded at the time.

On November 30, 2016, an employee was working on the magna vc line and received a crushing injury when a finger was pinched between the slide and the part that was being repaired. On December 23, 2016, the right index finger was amputated.

An employee was working on a trim cell unit where engine blocks are trimmed out. As he was picking up the block, he was wearing a hot mill style glove. His pinky went into the chain belt and was caught between the backside of the chain belt and the guard. His left pinky finger was amputated.

As an employee was verifying that the air pressure on a die-cast machine was at the correct level, the valve actuated and amputated the employee's third right-hand distal phalange.

An employee was walking down the hallway when they tripped and fell to the floor, fracturing their right wrist.

An employee was walking down the hall to retrieve a vacuum when they stumbled and fell to the floor. The employee suffered wrist bruises and a kneecap fracture that required surgery.

An employee was carrying furniture backward during a delivery when he tripped and broke his right ankle.

An employee was installing a compressor piston. He tripped and fell backward while the piston was in his lap. As he landed, the little finger of his left hand became caught between the piston and compressor piping resulting in a partial amputation of the fingertip. The employee required stitches and the fingertip was reattached.

An employee was doing an oil change. He was walking to get his oil jug when he tripped on an open lift pad, and fell to the ground landing on his right side. The employee sustained a broken right femur and was hospitalized.

An employee was adjusting the oscillator pressure injector on a die-cast machine when his right thumb contacted the adjustment handle. The machine oscillated and closed on his right thumb. The tip of the thumb was pinched and amputated between the die and the handle.

An employee in the melt department was getting ready to put a recirculation pump into the pump housing area. He first put the pump in a cabinet to warm it up to avoid thermal shock. It shifted and the cold refractory contacted the hot metal. Molten metal contacted the employee, resulting in third-degree burns between their knee(s) and ankle(s). The employee was wearing some personal protective equipment (PPE) at the time but this was breached by the molten metal.

On May 15, 2025, an employee was assisting with troubleshooting an issue with a die in a die casting machine. While unjamming the machine, the employee's finger was caught between a section of the die and a wooden spacer. The employee's left middle fingertip was amputated.

An employee was checking the die casting machine when the cavity access door closed behind him and the employee sustained eight fractured ribs. The employee was hospitalized.

An employee was using a vertical band saw to cut a piece of square metal tubing when their left hand contacted the saw blade and their middle finger was amputated.

The injured employee was assisting five other employees with bracing a wall panel that was being stood up. Another employee slipped on frost on the floor surface. The employees went to evacuate the area in anticipation of the wall panel falling over. The injured employee went to jump through a window opening within the wall panel and their lower half was crushed by the falling wall panel. The employee sustained a fractured pelvis.

An employee was using a vertical band saw to cut a thick piece of rubber material. While being cut, the material shifted, causing the employee s right hand to contact the moving blade. The employee's thumb was amputated below the knuckle. The employee was hospitalized, undergoing surgery.

A production sanitation employee was pre-rinsing an incline conveyor and noticed cheese stuck between the belt idler. The employee went to remove the cheese and their glove got caught and pulled their left forearm into the conveyor. The employee's arm was fractured. The machine was not locked out/tagged out at the time.

An employee was on a ladder, taking measurements for a new gutter installation. The ladder slipped out from under him and both he and the ladder fell to the ground. He was hospitalized with seven broken ribs and a broken clavicle.

An employee was unloading a truck for a delivery job. While moving boxes in the truck, the employee tripped over a pallet and fell out of the truck to the ground, resulting in four broken ribs.