Northeast Marine Construction

An employee was operating a sit-down type of material handling equipment (MHE). They were turning the MHE with the clamp attachment in the air when the MHE fell over onto its right side. The employee's right foot was caught under the battery cover of the MHE. The employee sustained a chemical burn from the battery and a fractured right ankle.

An employee was driving a snowmobile when it flipped over. The employee suffered a broken rib.

An employee was driving an unloaded forklift outside a building. During a left turn, the forklift drove off the paved area onto an unpaved surface, became unstable, and tipped over. The employee was pinned under the forklift and suffered two broken leg bones and a broken hip.

An employee was riding in a utility task vehicle when it overturned. The employee sustained a broken leg.

An employee was trimming tree branches from an aerial lift. As they were maneuvering the aerial bucket lift from inside, the truck drove over soft ground and tipped over. The bucket lift fell to the ground with the employee tied off inside, resulting in rib fractures.

A crew was installing drilled micropiles alongside an outdoor covered deck foundation. The injured employee was working the front of the drill when a loose section of casing dropped onto the tip of a rig wrench and pulled the wrench down to an embedded casing. The employee's left little finger was caught between the rig wrench and the embedded casing and was amputated above the top knuckle.

An employee was standing on an extension ladder, using a torquing tool to remove bolts that secured blades to a rotor. When the torquing tool activated, its reaction arm came around and pinched the employee's right middle finger against a lifting eye. His fingertip was amputated.

Employees were securing the fuel line of an outboard motor in preparation for removing the motor from a small vessel located in the equipment yard. A gasoline-related fire occurred and one employee sustained burns to both hands and forearms.

A marine diver/construction worker was working underwater, using a hydraulic dredge to clear sediment away from the base of a dam. The dredge's suction nozzle began migrating toward him, and then pulled in his right hand and forearm. He sustained compartment syndrome in the hand and forearm.

An employee was standing on a sheet of -inch by 4-foot by 8-foot plywood on top of a rebar mat, supervising his crew. As he was moving to alert the crew to an incoming overhead load, he stepped off the plywood and his left foot slipped through the rebar mat and landed on the rebar mat below. His left ankle was broken and dislocated.

A crew was installing drilled micropiles alongside an outdoor covered deck foundation. The injured employee was working the front of the drill when a loose section of casing dropped onto the tip of a rig wrench and pulled the wrench down to an embedded casing. The employee's left little finger was caught between the rig wrench and the embedded casing and was amputated above the top knuckle.

Two employees were working to change a tire on a mobile slasher saw. The slasher weighs around 2,000 pounds and is towed. Employee 2 was lifting the saw while the injured employee was placing a block of wood under the frame for support. The slasher then lowered onto the block and the injured employee's left thumb was crushed between the slasher frame and the wood block, leading to an amputation at the first knuckle.

An employee was using a metal shear when it amputated the tip of his right index finger.

An employee was using a crane to move a 44-foot, 3,343-pound I-beam. As the beam was moving west, it straightened out (north to south), beginning to swing south toward the northwest corner of a building. The crane then sent the beam southward, directly toward the corner of the building. The beam caught the tips of the employee's left index, middle, and ring fingers against the building. The last joints of the middle and ring fingers were amputated, and the last joint of the index finger was partially crushed.

An employee was standing on a step stool, removing the nuts and bolts from the frame of a solar panel that was being replaced. The employee's cheek made contact with a connector with damaged insulation. The employee was shocked, briefly lost consciousness, and fell to the ground, suffering an injury to the left shoulder.