Contact with hot objects or substances · Second degree heat (thermal) burns
At a glance
Federal OSHA recorded a severe workplace injury
at Goodyear Tire and Rubber Co., 2000 NW HIGHWAY 24, TOPEKA, KANSAS 66601
on — Second degree heat (thermal) burns, affecting the multiple body parts, n.e.c..
Final narrative
An employee was finishing a curing cycle and removing a steam line from a pot heater. The line was still under pressure at the time and the steam released, contacting the employee and causing second degree burns to the thigh and crotch area.
HospitalizedMultiple body parts, n.e.c.Steam, vapors-nonchemical
More severe injuries at Goodyear Tire and Rubber Co.
Two mechanics were working to replace bearings on a cooling rack on a mixer. The mechanics were rotating the chain around the sprocket by hand to get to the master link chain. The chain slipped and an employee's right hand was caught between the chain and the sprocket resulting in amputation of the middle fingertip.
An employee was operating a golf cart when the employee's knee struck an I-beam, fracturing the patella. The employee's knee was outside the vehicle at the time of the incident.
An employee had hooked his powered industrial vehicle (PIV) onto an empty rolling rack that is used to haul tire components. While attempting to pull it out, the tip of his right index finger was smashed between the empty rack and the light pole on the PIV. The right index fingertip was surgically removed.
An employee was placing extruded rubber into a storage rack when a broken spring caused a section of the rack to fall uncontrollably, pinching the employee's right middle finger between two sections of the rack. The employee's fingertip, including the nailbed, was amputated.
An employee was rolling a roll of liner so he could lift it using a forklift. The roll slipped off the carrier and injured the employee's lower left leg.
An employee connected a steam line to a hose to clean equipment when the fitting broke loose. They were struck by steam in the left inner thigh, resulting in burns that required hospitalization.
An employee was making tea when she noticed tea grinds were collecting on the side and water was no longer dripping through the funnel. The employee was checking the funnel when boiling water and tea grinds spilled onto the left side of her body. The employee sustained burns to her neck, back, and arm.
An employee had turned off the ball valve on a waterpipe system and was removing the plug when the coupling system attached to the strainer came apart. Hot water sprayed on his arm and back, resulting in first- and second-degree burns that required surgery.
An employee was using a shovel to remove waste vermiculite from molten zinc. The metal had been placed in a bin and partially hardened. The employee broke through the partially hardened metal; still-molten metal flowed to the employee's steel-toed right boot and entered through the cloth boot tongue. The employee suffered a third-degree burn to the right foot and was hospitalized.
More severe injuries in this industry (NAICS 326211)
On October 25, 2025, an employee was stringing up a new reel of tire tread on a machine. The employee pulled a 6-inch tail and proceeded to spool up the liner. As the machine was jogged to begin the liner wrapping process, the liner caught the employee's glove and pulled their right arm into the liner, causing a fracture to the arm.
An employee was adjusting a pallet on a conveyor when it came off the conveyor and struck his right ankle, breaking the tibia and fibula. The employee was hospitalized.
At 2:45 p.m., an employee was outside the plant during a break before his next shift. He was speaking with an associate when he suddenly fell from the third-level steps to the ground, striking his head on the concrete. The employee was hospitalized due to internal brain bleeding, a wound to the back of his head requiring staples, and heat-related dehydration.
Two employees were replacing a motor on an overhead conveyor. The old motor fell to the floor, causing a piece of the concrete floor to fly up and strike the injured employee in the face, around the eye. The injured employee sustained a right orbital fracture, a zygomatic arch fracture, and a sphenoid fracture. The employee was hospitalized and required surgery.
An employee was changing the bladder on a hydraulic press. As he lowered the bladder, his left foot was pinned between its bottom ring and the bottom mold of the press. The second toe on the foot was amputated.
An employee was working to remove a product blockage from a piece of equipment. The employee was struck by a metal bar near the deck of the pin mixer equipment and sustained blunt force trauma to the torso.
An employee was moving a rack onto a lower conveyor in the south heat treat area when their finger got caught between the part tray and the rollers, resulting in a fingertip fracture and amputation.
An employee was climbing a ladder to get on top of the breakroom. The ladder slipped, causing him to fall to the ground. The employee sustained fractures to his upper back, left foot, and ankle.
Two employees were removing a circuit breaker. The injured employee was using wrenches in the removal process. One of the wrenches contacted an adjacent door, resulting in an arc flash. The employee suffered burns to their neck, face, and ear, as well as momentary vision loss due to the flash.
An employee bent over to pick up a rubber mat from the ground. When he grabbed the corner of the mat, a rattlesnake hidden under it bit his left middle finger near the first knuckle. He was hospitalized.