Nemak USA Inc.

An employee in the melt department was getting ready to put a recirculation pump into the pump housing area. He first put the pump in a cabinet to warm it up to avoid thermal shock. It shifted and the cold refractory contacted the hot metal. Molten metal contacted the employee, resulting in third-degree burns between their knee(s) and ankle(s). The employee was wearing some personal protective equipment (PPE) at the time but this was breached by the molten metal.

An employee was sliding a steel work table when the table caught on an uneven surface and tipped over onto his left leg causing a fracture.

An employee was troubleshooting an issue with a dust collector when his hand was pulled into the pulley of the power transmission belt, resulting in a partial amputation to his right ring finger.

An employee entered the protective cell and was removing the steel liners from the die. The employee stepped up to the die, placing his left hand on the die surface to steady himself. The die core slide moved forward and the employee's fingers were caught between the core slide and the core guide plate, resulting in partial amputations to the left middle and ring fingers.

An employee was preparing a machine for setup and leaned forward to clean off an area. As he was backing out he misstepped over a hose, lost balance, and fell backward into the gravity slide table striking the left side of his back and head. The employee sustained a back contusion and a laceration (approximately 1 inch) to the head.

An employee was changing a saw blade when the saw machine activated. The employee's left ring and little fingers were amputated.

An employee was clearing a jam from the label cutting machine when their left middle finger was partially amputated.

Two employees were repairing the hydraulic engagement pins on a rented front-end wheel loader. The machine controls were activated to move the attachment pins and an employee's finger was caught between the pins and the bushings. Their right index finger was partially amputated.

An employee was cleaning the conveyor on a piece of equipment when they slipped and their right hand was pulled into the chain sprocket. The employee's fifth fingertip was amputated.

An employee was throwing blankets onto a blanket folding and stacking machine. A blanket got stuck in the machine and she attempted to remove it when the machine contacted her right little finger, resulting in a fingertip amputation.

An employee was working on a control panel for an electric furnace when he sustained an electric shock. The employee was hospitalized.

An employee was trimming manufactured parts using a two-hand control, C-frame trim press. They were manipulating parts in the machine when their hand contacted the controls that energized the machine. The employee sustained amputations to their left index finger and left thumb.

Two employees were operating an aluminum die casting machine when a piston that pushed molten aluminum into the mold stopped dispensing aluminum correctly. After they had spent several hours fixing the issue, the machine cycled and the die closed on one employee's right hand. The employee suffered amputations to the index fingertip and the thumb at the knuckle.

An employee was operating a mold machine when a pouring ladle that was coated with a water-based paste was submerged in molten aluminum. The moisture caused an explosion, resulting in severe burns over his body.

On September 10, 2024, at approximately 5:55 AM, an employee suffered burns to his right hand as he was removing a ladle from a furnace and the cup made contact with the side of the furnace, splashing molten aluminum into his glove. The employee was hospitalized with burns to his right hand.

The injured employee was assisting five other employees with bracing a wall panel that was being stood up. Another employee slipped on frost on the floor surface. The employees went to evacuate the area in anticipation of the wall panel falling over. The injured employee went to jump through a window opening within the wall panel and their lower half was crushed by the falling wall panel. The employee sustained a fractured pelvis.

An employee was using a vertical band saw to cut a thick piece of rubber material. While being cut, the material shifted, causing the employee s right hand to contact the moving blade. The employee's thumb was amputated below the knuckle. The employee was hospitalized, undergoing surgery.

A production sanitation employee was pre-rinsing an incline conveyor and noticed cheese stuck between the belt idler. The employee went to remove the cheese and their glove got caught and pulled their left forearm into the conveyor. The employee's arm was fractured. The machine was not locked out/tagged out at the time.

An employee was on a ladder, taking measurements for a new gutter installation. The ladder slipped out from under him and both he and the ladder fell to the ground. He was hospitalized with seven broken ribs and a broken clavicle.

An employee was unloading a truck for a delivery job. While moving boxes in the truck, the employee tripped over a pallet and fell out of the truck to the ground, resulting in four broken ribs.