Briess Industries, Inc.

An employee was shutting down at the end of a shift when he noticed dust was jamming his machine. When the employee cleared the jam, his fingers made contact with the rotary airlock blade, resulting in the amputation of the middle finger right below the fingernail and the ring fingertip.

An employee was installing a new gear in a hand-operated flake mill and trying to line up the gear with a worm screw shaft approximately 18 inches long and weighing 30 pounds. The employee's left thumb was pinched between the shaft and the gear, resulting in a fingertip amputation.

An employee contacted the moving auger while cleaning it. The employee sustained three fractured fingers and tendon and nerve damage. The auger was not locked out/tagged out at the time.

An employee was preparing a cleaning solution for a weekly scheduled cleaning when two incompatible solutions were mixed, exposing the employee to chemical vapors. The employee experienced difficulty breathing.

An employee was repairing a leaking valve when another valve opened and hot water was pumped into the system. The hot water scalded the employee, who suffered second degree burns.

An employee was performing finishing work on a residential driveway when they began to experience body cramps and were hospitalized for heat stress and dehydration.

An employee was staking tomato plants on a farm. The employee began to feel sick and collapsed, suffering from dehydration and heat shock.

An agent was participating in SWAT team selection and was performing various physical fitness skills including running and exercise intervals. The agent experienced dehydration and a muscular injury that required hospitalization.

An employee was traveling back from work when they became ill and experienced dizziness due to heat exhaustion.

On September 26, 2023, an employee was delivering packages when he began to feel ill with a pain in his side. He was hospitalized for heat exhaustion and dehydration.

During a dust baghouse inspection, a discharge chute plugged up with grain debris. An employee went to remove the debris and his finger got caught in the rotary airlock. The employee sustained a laceration to their right middle finger that resulted in a partial amputation.

An employee was shutting down at the end of a shift when he noticed dust was jamming his machine. When the employee cleared the jam, his fingers made contact with the rotary airlock blade, resulting in the amputation of the middle finger right below the fingernail and the ring fingertip.

An employee was swapping barrels under a dust cyclone. The employee turned around and ran into an adjacent barrel and lost balance. His right hand went up the sock that surrounded the bottom of the dust collector and the rotating airlock blade partially amputated his index and middle fingers. The machine was not guarded at the time.

An employee was installing a new gear in a hand-operated flake mill and trying to line up the gear with a worm screw shaft approximately 18 inches long and weighing 30 pounds. The employee's left thumb was pinched between the shaft and the gear, resulting in a fingertip amputation.

An employee was entering an area through an opening in a plastic curtain barricade. The employee's foot got caught on the bottom of the curtain and she fell to the concrete floor, breaking both wrists.

The injured employee was assisting five other employees with bracing a wall panel that was being stood up. Another employee slipped on frost on the floor surface. The employees went to evacuate the area in anticipation of the wall panel falling over. The injured employee went to jump through a window opening within the wall panel and their lower half was crushed by the falling wall panel. The employee sustained a fractured pelvis.

An employee was using a vertical band saw to cut a thick piece of rubber material. While being cut, the material shifted, causing the employee s right hand to contact the moving blade. The employee's thumb was amputated below the knuckle. The employee was hospitalized, undergoing surgery.

A production sanitation employee was pre-rinsing an incline conveyor and noticed cheese stuck between the belt idler. The employee went to remove the cheese and their glove got caught and pulled their left forearm into the conveyor. The employee's arm was fractured. The machine was not locked out/tagged out at the time.

An employee was on a ladder, taking measurements for a new gutter installation. The ladder slipped out from under him and both he and the ladder fell to the ground. He was hospitalized with seven broken ribs and a broken clavicle.

An employee was unloading a truck for a delivery job. While moving boxes in the truck, the employee tripped over a pallet and fell out of the truck to the ground, resulting in four broken ribs.