ALL AMERICAN POLY CORPORATION

An employee was evaluating an issue with a shaft in a winder. The employee's left index, middle, and ring fingers got caught between the belt drive and sprocket, resulting in one finger amputation at the first joint.

Two employees were installing a new plastic roll on a winder machine. One of them was pulling the film with her left hand from the output side of the machine; the film and the rotating member of the winder caught her left hand, breaking both bones in her left forearm.

An employee was drilling a hole in a can containing aerosol spray glue. The can exploded, causing second-degree burns to the employee's arms, face, and neck.

An employee was descending a fixed caged ladder when he missed the top rung and began to fall. He grabbed onto a vertical member of the cage assembly to catch himself and caught his right pinky in a 1/2-inch gap between the upright and a toe board section. His right pinky fingertip was amputated.

An employee was clearing debris from the line. The blower did not come to a complete stop and the employee's left hand was lacerated.

On December 19, 2023, an employee was setting up a copper wire drawing machine when his left ring finger was pinched between a copper wire and a machine part. The employee's finger was partially amputated.

An employee was examining a machine when a part moved up and amputated a fingertip on their left hand.

An employee was checking the gusset seal on a machine. He moved to the next cross sealer and the machine activated, causing an amputation to a left-hand finger. The employee was hospitalized.

An employee was evaluating a coiling machine to verify that the blade was present inside it. The machine's weld function was activated, and the machine crushed the employee's fingers, resulting in the amputation of the left middle and ring fingers.

An employee's right hand was caught in a wire drawing machine, resulting in amputation.

A subcontracted engineer was advising maintenance how to make a modification to the embossing roll system on a new line. Maintenance was bringing the motor and gearbox down with a crane. The load shifted when it was a few inches from the ground. The engineer went to catch/maneuver the gearbox and the fingers on his left hand were crushed between the I-beam base of the gearbox and the concrete floor. A finger was amputated.

On July 30, 2025, an employee was assisting co-workers in using a hoist to position an injection molding tool onto a work table. As the tool was being lowered, the slide section shifted, trapping and amputating the employee's right thumb tip.

An employee was manually lifting a film roll when their right middle fingertip was pinched between the roll and a metal beam, resulting in a fingertip amputation.

At about 10:00 a.m. on July 13, 2025, an employee was cleaning the adhesive from running rollers using a rag soaked in cleaning solvent to prevent contamination. The rag was caught between two rollers and pulled the employee's right hand between the rollers. The employee sustained right hand crushing injuries, de-gloving injuries (palmer and dorsal sides), and fractures. The employee was hospitalized and required surgery. The machine was not locked out/tagged out at the time.

An employee working on a sheet line was removing masking from the underside of plastic sheeting that was being lifted by a vacuum lift. The plastic sheet measured 4 feet wide, 14 feet long, and approximately 1 inch thick, and it weighed approximately 300 pounds. The vacuum lost suction and dropped the plastic sheet onto the employee's arm, pinning it between two sheets and resulting in a broken right forearm.

An employee tripped over a stool and fell on the floor, resulting in a left displaced mid-cervical femoral neck fracture.

An employee was installing fence posts when they stepped into a recently dug hole that was not visible due to rainfall. The employee's leg was fractured.

An employee assisted in cleaning material from a conveyor pit. After the pit was cleaned, the employee proceeded to replace metal safety plates to ensure other employees did not fall into the pit. While replacing one of the last plates, the employee mis-stepped and fell approximately 5 feet into the pit. The employee was hospitalized with back/side bruising, elbow bruising, bone bruises, and/or fractured ribs.

An employee was inspecting a breaker box and turning on/off a circuit breaker when he was electrocuted.

An employee was walking on the sidewalk. When they stepped off the curb, they fell to the ground, resulting in fractures to their tibia, fibula, and a metatarsal.