ACCORD STEEL AND PRECAST ERECTORS, INC.

An employee was setting a small piece of iron around the perimeter of the building when he slipped and fell. The sleever bar in his toolbelt impaled his armpit.

An employee fell 17 feet to the floor below while releasing a load of steel decking that had been hoisted by a crane. The employee suffered broken bones and internal injuries.

The employee was on top of a rail car to level the grain that was deposited into the car when they fell 13-15 feet to the ground. The employee sustained a right leg fracture.

An employee was on an extension ladder installing a satellite dish on a roof when they fell approximately 12-15 feet to the ground. The employee sustained fractures.

An employee was setting a 5-foot pry bar into a precast concrete slab and stood on the end of the pry bar to move the slab into place. The pry bar slipped out causing the employee to fall backward 15.5 feet to the dirt ground. The employee was hospitalized with a broken leg.

An employee was on a step ladder to measure and mark a crane rail for modification. The employee fell approximately 12 to 15 feet to the ground, resulting in a fractured right hip.

An employee was on a trailer securing a load of logs when they fell approximately 9-12 feet to the ground. The employee sustained brain hemorrhaging and lacerations to the thigh and above the eye. The employee was hospitalized.

An employee fell from a step ladder while reaching for a tie-off point. He impacted the ground, and landed on his bolt bag which contained tools. The employee was hospitalized with fractured ribs, and a lacerated spleen and kidney.

An employee was attempting to lift a steel beam from a horizontal, stacked position to a vertical position using a crane. They had placed two hooks on the east side of the beam on the flange. As the employee was hoisting the crane, the beam began to shift and pulled the employee forward onto the stack. When the material shifted, the hooks released and the material fell, pinning the employee between the two beams. The employee was hospitalized with soft tissue contusions on their proximal right thigh and interior left thigh.

An employee was standing on the surface of a steel beam about two feet wide. He slipped and fell backward, landing on the concrete ground about 20 feet below. The employee sustained a broken pelvis.

An employee was unloading a rebar delivery from a flatbed, 19-wheel trailer. The employee rigged the load with wire rope chokers. The load was picked up 3-4 feet above the trailer deck by a crane. The load began to swing and the employee grabbed onto it to prevent it from being pushed off the trailer deck. The crane continued to lift the load, and the employee let go so the crane did not lift him to the third story. The employee fell approximately 12 feet to the ground below, resulting in a back injury and fractured vertebrae.

An employee was attaching a steel angle plate weighing (approximately 200 pounds) to the end of a structural member (5,000 pounds) and was supported by dunnage. The dunnage was a crane mat (11 inches tall) with a 4x6 board on top of it and it supported five identical members. The main piece was 30.75 feet long, 37.25 feet tall, and 1 food wide. As the employee slid the piece of metal on top of the member to begin attaching it, the entire member began to tip over. The employee went to stop the main piece from tipping over and it landed on his ankle, fracturing it.

An employee fell while exiting a trailer. The employee landed on their left side on the pavement, suffering multiple broken ribs on the left side. The employee was hospitalized.

Two employees were setting up a mandrel in the spindle of a machine. The mandrel was side-shifted while an employee's hand was on the mast of a powered industrial truck. The employee suffered crushing injuries that resulted in amputations to the middle and ring fingertips.

An employee had been loading a double deck press. The employee saw a mold had been sent in with the C-hook still attached on the belly bar. As he went to remove the hook from the mold, his right thumb got caught on the C-hook. The employee's thumb was partially amputated.

An employee was operating a roller and paving a small pathway next to a pavilion. The ground was on a slight pitch, causing him to reach up toward the roll cage to stabilize himself. His right fifth finger was pinched between the roll cage and the rafter of the pavilion. The employee sustained a partial degloving injury with partial traumatic amputation.

An employee was delivering home heating fuel when bees came from the ground and stung the employee's face, neck, torso, and hands. The employee proceeded to shut off the oil flow before losing consciousness. They were hospitalized due to an anaphylactic reaction.