ACCORD STEEL AND PRECAST ERECTORS, INC.

An employee was setting a small piece of iron around the perimeter of the building when he slipped and fell. The sleever bar in his toolbelt impaled his armpit.

An employee lost balance while on a ladder connecting steel and fell approximately 14 feet to the floor, suffering a compound fracture to the right leg.

An employee was transitioning from a ladder onto a roof when the ladder slipped and they fell approximately 20 feet to the ground. The employee was hospitalized with fractures to their pelvis and heel.

An employee was tearing down shingles when they fell approximately 18 feet from a roof to the ground, sustaining a broken ankle.

An employee was climbing a ladder to bring material onto a roof. The ladder slid and the employee fell 16 feet to the ground, resulting in a broken knee.

An employee was performing an inspection of a bridge crane while working from a 19-foot scissor lift. The employee was going to use a pendant to move the crane to access a different portion of the crane for visual inspection. The scissor lift guard rails were below the girder of the crane to avoid contact. The tow arm for the crane collectors contacted the guardrail of the scissor lift and caused it to tip over. The employee stayed inside the scissor lift basket as he fell to the floor. The employee sustained fractures to the right arm and hip.

An employee was on a forklift that was elevated approximately 20 feet and was auditing inventory. The forklift malfunctioned and the employee fell down to the surface below, causing them to sustain multiple fractures.

An employee fell from a step ladder while reaching for a tie-off point. He impacted the ground, and landed on his bolt bag which contained tools. The employee was hospitalized with fractured ribs, and a lacerated spleen and kidney.

An employee was attempting to lift a steel beam from a horizontal, stacked position to a vertical position using a crane. They had placed two hooks on the east side of the beam on the flange. As the employee was hoisting the crane, the beam began to shift and pulled the employee forward onto the stack. When the material shifted, the hooks released and the material fell, pinning the employee between the two beams. The employee was hospitalized with soft tissue contusions on their proximal right thigh and interior left thigh.

An employee was standing on the surface of a steel beam about two feet wide. He slipped and fell backward, landing on the concrete ground about 20 feet below. The employee sustained a broken pelvis.

An employee was unloading a rebar delivery from a flatbed, 19-wheel trailer. The employee rigged the load with wire rope chokers. The load was picked up 3-4 feet above the trailer deck by a crane. The load began to swing and the employee grabbed onto it to prevent it from being pushed off the trailer deck. The crane continued to lift the load, and the employee let go so the crane did not lift him to the third story. The employee fell approximately 12 feet to the ground below, resulting in a back injury and fractured vertebrae.

An employee was attaching a steel angle plate weighing (approximately 200 pounds) to the end of a structural member (5,000 pounds) and was supported by dunnage. The dunnage was a crane mat (11 inches tall) with a 4x6 board on top of it and it supported five identical members. The main piece was 30.75 feet long, 37.25 feet tall, and 1 food wide. As the employee slid the piece of metal on top of the member to begin attaching it, the entire member began to tip over. The employee went to stop the main piece from tipping over and it landed on his ankle, fracturing it.

An employee fell while exiting a trailer. The employee landed on their left side on the pavement, suffering multiple broken ribs on the left side. The employee was hospitalized.

Two employees were setting up a mandrel in the spindle of a machine. The mandrel was side-shifted while an employee's hand was on the mast of a powered industrial truck. The employee suffered crushing injuries that resulted in amputations to the middle and ring fingertips.

An employee had been loading a double deck press. The employee saw a mold had been sent in with the C-hook still attached on the belly bar. As he went to remove the hook from the mold, his right thumb got caught on the C-hook. The employee's thumb was partially amputated.

An employee was operating a roller and paving a small pathway next to a pavilion. The ground was on a slight pitch, causing him to reach up toward the roll cage to stabilize himself. His right fifth finger was pinched between the roll cage and the rafter of the pavilion. The employee sustained a partial degloving injury with partial traumatic amputation.

An employee was delivering home heating fuel when bees came from the ground and stung the employee's face, neck, torso, and hands. The employee proceeded to shut off the oil flow before losing consciousness. They were hospitalized due to an anaphylactic reaction.