Ignition of vapors, gases, or liquids · Second degree heat (thermal) burns
At a glance
Federal OSHA recorded a severe workplace injury
at The Williams Companies, 23759 Weld County Road 34.5, LA SALLE, COLORADO 80645
on — Second degree heat (thermal) burns, affecting the multiple body parts, n.e.c..
Final narrative
Employees were preparing a pig receiver and pig launcher. The block valves had been closed, and the receiver and launcher had been blown down; liquids were draining from the opening of the launcher. A forklift was being used to open the receiver hatch. The hatch struck the forklift's forks, and liquids at the receiver and launcher ignited. An employee suffered second-degree burns to the face and right hand, as well as first-degree burns to the left and right lower legs, and was hospitalized.
HospitalizedMultiple body parts, n.e.c.Chemicals and chemical products, unspecified
An employee was transporting used filter media (containing pyrophoric iron sulfide) from an inlet gas separator in the bed of a truck. The material ignited. While the employee was removing items from the truck bed, a gas can was exposed to the fire and off-gassing vapors ignited. The employee suffered first- and second-degree burns to both arms, the chest, the neck, and the right ear. The employee was hospitalized.
An employee was using a pipe wrench to loosen a piece of pipe above a 2-inch swedge. The wrench slipped and he lost his balance and fell backward, turning as he fell. His left side came into contact with a guardrail behind him and he suffered four rib fractures. He was hospitalized.
An employee was cleaning a cordless drill. As they applied brake fluid to the drill and pulled the trigger, the fluid ignited. The employee suffered burns to the face, hands, and arms.
An employee was spraying glue to the floor of an enclosed cargo trailer. The fumes made contact with the heater causing a flash fire. The employee suffered burns to their face and right hand.
An employee was replacing a valve in the gas line to the fryer. The shutoff valve malfunctioned resulting in a gas leak that then ignited. The employee sustained burns requiring hospitalization.
An employee was operating an aerial work platform. While the employee was maneuvering the lift through a set of double doors, their head was caught between the door frame and the platform's vertical mast. The employee suffered a skull fracture that required surgery.
An employee was transporting used filter media (containing pyrophoric iron sulfide) from an inlet gas separator in the bed of a truck. The material ignited. While the employee was removing items from the truck bed, a gas can was exposed to the fire and off-gassing vapors ignited. The employee suffered first- and second-degree burns to both arms, the chest, the neck, and the right ear. The employee was hospitalized.
An employee was using a pipe threading machine to thread a 2-inch diameter gas pipe during the rebuilding of a gas meter. The pipe was in a vise mounted on the back of the crew truck. A few pieces of metal chips or shavings caused the threading machine to jam. The employee started to back the pipe up, but it jammed in that direction as well. While reaching to pull the handle back up into place to try and start again, the machine rotated about an inch and pinched his middle fingertip against the edge of the truck s back step. The employee's fingertip was partially amputated without loss of bone.
The injured employee was manually lowering a ramp on a heavy equipment trailer with the assistance of another employee. The injured employee was standing behind the trailer ramp. After removing the safety pins, the ramp descended quickly and struck the injured employee, causing them to fall to the ground. The employee was hospitalized with fractures to their sternum and L1 vertebra.
An employee was delivering materials. He was doing his pre-delivery inspection on the roof of the jobsite (a warehouse) when he fell through a plexiglass skylight. He landed on his feet on the concrete floor 14 feet below. The employee sustained fractures to his spine, left ulnar/radius, and right heel. The employee required surgery.
An employee was removing packaging from a roll of printing substrate. The blade of their utility knife got stuck. The employee used both hands to free the knife and the blade partially amputated their left little fingertip.
A concrete batch plant operator was assisting with clearing spoil piles using a skid steer. The skid steer backed into a stationary screen plant. The employee's left little finger was crushed between the controls of the skid steer and the screen plant, resulting in a fracture and laceration. The employee's finger was surgically amputated.
An employee was standing on an extension ladder, using a torquing tool to remove bolts that secured blades to a rotor. When the torquing tool activated, its reaction arm came around and pinched the employee's right middle finger against a lifting eye. His fingertip was amputated.