Direct exposure to electricity, unspecified · Second degree electrical burns
At a glance
Federal OSHA recorded a severe workplace injury
at Helix Electric, Inc., 7879 Wardleigh Rd, HILL AIR FORCE BASE, UTAH 84056
on — Second degree electrical burns, affecting the multiple body parts, n.e.c..
Final narrative
An employee had been connecting cables between a load bank and a transformer (neither were connected to an energy source). After that he began to roll out and position cables to connect the transformer to an electrical switchboard. While positioning cables at the rear of the switchboard in preparation for making the final connections, he contacted an energized buss bar. The employee sustained first degree burns on both arms, with second degree burns on his forearms and hands. He also sustained first and second degree burns on the left side of his chest. Additionally, he sustained two exit wounds on his left leg, one on the knee and the other just above the knee.
HospitalizedMultiple body parts, n.e.c.Power lines, transformers, convertors
An employee was using a pipe cart to move conduit. The uprights on the cart shifted and struck him in the throat, fracturing his larynx. He was hospitalized for surgery.
An employee was installing a 15-amp breaker in an electrical panel when a 12-gauge ground wire touched the positive busbar of the panel, resulting in an arc flash. The employee sustained a second-degree burn to their left hand.
An employee was repairing an HVAC system in the drop tile ceiling of a conference room when they were shocked, causing them to fall from the ladder. The employee sustained burns to their right middle and ring fingers.
An employee was replacing a contactor inside an electrical panel attached directly to a press. The press itself was receiving power from another main panel. After replacing the contactor, the employee flipped the switch and an arc flash occurred, burning the employee's elbow, bicep, and neck.
An employee was attempting to switch a medium-voltage primary cable and install a 200-amp fuse barrel. The employee contacted the bottom of the switch gear cradle for the fuse barrel, causing an arc blast. The electricity entered the employee s left hand and exited his big toes, resulting in electric shock and burns to the left hand, arm, shoulder, and both feet. The employee was hospitalized.
On December 6, 2023, an employee of Duke Energy was working on a single-phase 120-/240-volt parallel service re-tap when a secondary flash occurred in an underground service. The employee suffered a second-degree burn to the face and was hospitalized.
More severe injuries in this industry (NAICS 238210)
An employee was troubleshooting the control setup for a variable air volume box above a ceiling. The employee's hand came into contact with an exposed, energized 277-volt wire that had loosened from its terminal on the box's assembly. He was shocked and fell off a ladder. His left hand passed across the ceiling grid and was lacerated. He also suffered an electrical burn to the right hand and was hospitalized.
An employee was moving a scissor lift through a doorway. The employee was pinned between the scissor lift and the doorframe, sustained a back injury, and was hospitalized.
An employee was standing on an A-frame ladder approximately 6 feet above the floor while he attached a suspended light fixture to the ceiling. The employee lost balance, and fell to the tiled floor below, sustaining blunt force trauma to his head.
An employee was inspecting the overhead area of a single-person lift and repositioning the lift through a double doorway. As they were transitioning through the doorway, they were caught between the doorframe and the vertical mast of the lift. The employee was hospitalized with injuries to the nose, left maxillary sinus, left orbital bone, and left jaw, with fractures at the maxillary sinus area.
The injured employee was performing routine maintenance on a fan belt/pulley. The injured employee and another person were moving the pulley back and forth manually to find a bearing issue. The injured employee's left ring finger got caught between the belt and the pulley wheel, resulting in a soft tissue amputation.
An employee was on a four-step work stand while sanding an area of an aircraft. He was climbing down the work stand when he tripped over an air hose and fell to the level below, resulting in a fractured femur.
An employee was scanning the placards of pallets of mail bundles when a forklift approached from the opposite side and began lowering and pushing his pallet load forward. It struck the pallet the employee was working on, causing it to shift and strike her. She fell to the ground and sustained a left hip fracture that required surgery.
An X-ray machine had lost power and an employee went to replace the power supply. While replacing a cable on the power supply assembly, the employee's right hand contacted the grounding terminals coming out of the back of the power supply assembly and they received an electric shock. The employee was hospitalized.
An employee was servicing equipment and had disconnected a 4-inch line. A proportional control air valve on the equipment actuated, releasing a large volume of air at 99 psi into the 4-inch braided stainless steel line hanging down from the valve. The sudden release of pressure caused the line to whip and strike the employee's face. He was hospitalized due to an orbital bone fracture requiring surgery. The equipment was not locked out/tagged out at the time.
An employee was performing janitorial duties and carrying bathroom supplies when he slipped on a guardrail mounting post and fell on his side. The employee's hip was fractured and required surgery.