Ellis Processing & Material Handling LLC

Employees were unloading a barge into a charge truck on the scrap dock. The crane operator was stepping out of the cab to relay a message to a dockhand. When he returned to the cab of the crane his shirt caught on one of the joysticks and pulled the grapple toward the machine. The grapple struck the charge truck driver resulting in a head laceration and contusion resulting in hospitalization.

An employee was on a two-step ladder performing cleaning activities in the de-oiler machine. The employee fell back and his right arm was caught in the equipment, resulting in a right forearm fracture that required surgery.

An employee was changing an insert in the tool head of a CNC machine. The employee had stepped up approximately 28 inches onto the door track of the machine. When the employee went to step back down to the floor, they lost balance and fell backward onto a rack of metal parts. The employee sustained a compression fracture to the spine.

An employee was packaging steel coils on a turntable. As he walked across the turntable, he slipped and fell onto a coil. His left bicep was lacerated by the slit edge of a coil.

An employee was monitoring a lumber-stacking machine when they slipped and fell into an unbanded bundle of lumber. The outer row of lumber then fell on their left leg, fracturing their leg and ankle.

An employee was putting parts away in a warehouse. He tripped and fell into metal shelving, resulting in a broken arm.

An employee was sorting sucker rods. His right hand was caught in the area where the rod hits up against the frame and his index fingertip was amputated just below the nail.

An employee was using a powered miter saw to cut 2x4's. The saw blade hit something inside a board (possibly a hidden nail) and jumped, causing a laceration to the employee's left forearm. The employee was hospitalized with soft tissue and tendon injuries that required surgery.

A crane had been used to set a steel plate on a steel frame. An employee was trying to remove a clamp from the plate when the plate fell and crushed the tip of his left little finger. The employee sustained a fingertip amputation.

An employee was operating a scissor lift, raised to a height of about 15 feet, to inspect an overhead crane rail. The crane itself was being moved. Its hook swung into the scissor lift s arms, causing the lift to tip over onto its side, which in turn caused the lift and the employee to fall to the floor. The employee suffered injuries including broken ribs, spinal fractures, scapula fractures, and internal injuries.

A technician was operating a crane hoist to lift/remove a cylinder head from the main engine (port). The load was lifted at an angle, causing the cylinder head to get stuck on the cylinder head studs. When it became free from the studs, the cylinder head swung. It struck the technician and caught them against the cabinet door. This resulted in an amputation of their left index fingertip at the distal knuckle.

An employee was operating an ironworker (steel punching/shearing) machine. A piece of the tooling broke off and struck the employee's neck; a fragment was lodged in his neck. The employee was hospitalized and required surgery.

On October 25, 2025, an employee was stringing up a new reel of tire tread on a machine. The employee pulled a 6-inch tail and proceeded to spool up the liner. As the machine was jogged to begin the liner wrapping process, the liner caught the employee's glove and pulled their right arm into the liner, causing a fracture to the arm.

An employee was doing a cable change on top of an electric overhead traveling (EOT) crane. They were positioned between the cable drum and the drive shaft. While rotating the cable drum, the employee reached for the new cable that was to be installed. The grease fitting on the drive shaft caught their fall harness and pulled them underneath the drive shaft. The employee was pinned between the drive shaft and two pieces of angle steel, resulting in a fracture to their left hip.

An employee was helping two other employees to push a pallet of tile on a loading dock. He suffered a broken fibula and was hospitalized.

On October 5, 2025, an employee was pulling a pressure washer hose when it it disconnected from the cooker. The employee was struck by jets of high-pressure water, resulting in lacerations to their left thigh requiring surgery. The employee was hospitalized.