Landoll Corporation

An employee had been moving scrap to a storage area in the fabrication department. While moving the hoist back to the work area, a hook at the end of the hoist got caught on a short rack (about 2 feet tall) of flat steel. The rack was pulled over and struck the employee, knocking him to the concrete floor. The rack then landed on the employee, fracturing both of his legs below the knees.

An employee was using a saw to cut square steel tubing. He pulled a cut tube toward himself to ensure it was cut. Another tube came through and crushed his left ring and little fingers against the side of the machine. Both fingers were medically amputated.

An employee fell from the upper deck of a drop-deck trailer, landing on the ground on his left side. He suffered arm, rib, and pelvis fractures.

An employee was moving a table (on rollers) that was loaded with square tubing into his work area. The square tubing shifted and a piece rolled and smashed right thumb.

An employee was in the process of loading a gang bar onto a paint rack in the shop using an overhead crane rigged with a magnet. The gang bar was placed on the rack out of position. The employee released the lifting device and attempted to reposition the gang bar without the lifting device. In the process of repositioning the gang bar, one end came out of the rack and fell pinching the employee's fingertip between the gang bar and the rack resulting in a right middle fingertip amputation.

An employee was collecting trash when they were struck by a rolling utility trailer. The employee sustained a right ankle fracture.

An employee was unrigging steel when an 8-inch by 50-foot, 4,875-pound piece of steel rolled onto their left leg, resulting in a fracture.

An employee was connecting a dolly to a trailer. The equipment rolled away, causing the employee's left index finger to be crushed between the trailer and the dolly. The employee sustained amputation of the fingertip.

On October 17, 2023, at 9:55 p.m., an employee was working on a ramp while moving merchandise from a cargo loader to a dolly. The employee was putting the locks on the dolly and transferring a unit load device containing packages when she realized the lock was in the down position. As she attempted to fix the lock, the unit load device started moving toward the dolly, and the employee became wedged between the dolly and the device. The employee suffered an injury to her lower left leg.

Two employees were shaking out steel beams and standing them vertically. One beam was hit, causing the other beams to fall. A beam then rolled over an employee's left shin and fractured it. The employee was hospitalized and required surgery.

An employee was welding lift arms when their shirt caught fire due to welding sparks or heat, resulting in thermal burns to their upper chest.

An employee was climbing up a fixed ladder alongside a building to inspect a roof leak. The employee fell off the ladder and landed on the ground about 15 feet below. The employee was hospitalized with fractures to both wrists.

On September 16, 2025, an employee went to pull a weld stand when he tripped and fell, landing on the floor on his right hip. The employee suffered hip and fibula fractures that required hospitalization and surgery.

An employee was accessing a tensioned hook that required a hoist mechanism to be engaged. He was unhooking the lift hook from a shelf column when the "up" button was pressed, which released the tension on the pneumatic air hoist. The employee's right index finger was caught between the hook and the column, resulting in a soft tissue amputation and fracture to the fingertip.

A crane was lifting a pole out of a zinc bath in the galvanizing department when the chain attached to the pole broke. The pole fell back into the bath and liquid zinc splashed onto an employee, who suffered third-degree burns to an arm, the abdomen, the torso, the upper left side of the chest, an ear, the neck, and a hand.

An employee was working to remove a product blockage from a piece of equipment. The employee was struck by a metal bar near the deck of the pin mixer equipment and sustained blunt force trauma to the torso.

An employee was moving a rack onto a lower conveyor in the south heat treat area when their finger got caught between the part tray and the rollers, resulting in a fingertip fracture and amputation.

An employee was climbing a ladder to get on top of the breakroom. The ladder slipped, causing him to fall to the ground. The employee sustained fractures to his upper back, left foot, and ankle.

Two employees were removing a circuit breaker. The injured employee was using wrenches in the removal process. One of the wrenches contacted an adjacent door, resulting in an arc flash. The employee suffered burns to their neck, face, and ear, as well as momentary vision loss due to the flash.

An employee bent over to pick up a rubber mat from the ground. When he grabbed the corner of the mat, a rattlesnake hidden under it bit his left middle finger near the first knuckle. He was hospitalized.