Pre-Con Construction, Inc.

The injured employee was acting as a spotter for another employee that was using a forklift to move crane plates. The injured employee went to walk on top of staged bracing poles that had been stacked. The top layer of bracing shifted when stepped on, causing the employee to lose balance and fall. During the fall, one of the bracing poles dislodged and landed on the employee s left leg, causing a compound fracture.

An employee was walking along a trench inspecting the trench box in the excavation when he tripped and fell toward the trench. As the employee was falling head-first into the trench, he attempted to get a hold of the fall protection cable. The cable then looped around his left hand and the employee fell approximately 8 feet into the trench before the fall protection engaged. The employee suffered amputations of his left index, middle, ring, and little fingers.

A ranger was performing back-country patrol duties while hiking. As they were climbing a technical rock patch, a rock handhold broke, causing the employee to fall approximately 15 feet before their belay engaged. The employee contacted a rock, resulting in a fracture to the right ilium as well as a subcutaneous hematoma to the right gluteal region.

Employees were erecting structural steel. The injured employee was sitting on a 12" wide horizontal member and lining up an I-beam brace as it was suspended by an overhead crane. He leaned left to push the end of the brace. The end of the suspended brace swung away from him, causing him to lose balance and fall 8 feet. His personal fall arrest system arrested his fall, but he swung into a piece of duct work during the fall that resulted in a concussion.

On September 12, 2022, an employee was on a metal roof, installing a standing seam and insulation. He lost his balance and fell toward the third floor slab, which was 10 feet from the roof. His fall protection caught him and left him suspended about 2 to 4 feet from the slab. He suffered a brain bleed and a spinal fracture in his lower back. He was hospitalized.

An employee was working from a bucket lift, removing a tree in sections. He lost his balance while pushing on a section and fell. His fall protection caught him and he swung into a tree, suffering an injury that caused head, neck, and leg pain, as well as loss of consciousness while he was at the hospital.

An employee fell from a step ladder while reaching for a tie-off point. He impacted the ground, and landed on his bolt bag which contained tools. The employee was hospitalized with fractured ribs, and a lacerated spleen and kidney.

An employee was attempting to lift a steel beam from a horizontal, stacked position to a vertical position using a crane. They had placed two hooks on the east side of the beam on the flange. As the employee was hoisting the crane, the beam began to shift and pulled the employee forward onto the stack. When the material shifted, the hooks released and the material fell, pinning the employee between the two beams. The employee was hospitalized with soft tissue contusions on their proximal right thigh and interior left thigh.

An employee was standing on the surface of a steel beam about two feet wide. He slipped and fell backward, landing on the concrete ground about 20 feet below. The employee sustained a broken pelvis.

An employee was unloading a rebar delivery from a flatbed, 19-wheel trailer. The employee rigged the load with wire rope chokers. The load was picked up 3-4 feet above the trailer deck by a crane. The load began to swing and the employee grabbed onto it to prevent it from being pushed off the trailer deck. The crane continued to lift the load, and the employee let go so the crane did not lift him to the third story. The employee fell approximately 12 feet to the ground below, resulting in a back injury and fractured vertebrae.

An employee was attaching a steel angle plate weighing (approximately 200 pounds) to the end of a structural member (5,000 pounds) and was supported by dunnage. The dunnage was a crane mat (11 inches tall) with a 4x6 board on top of it and it supported five identical members. The main piece was 30.75 feet long, 37.25 feet tall, and 1 food wide. As the employee slid the piece of metal on top of the member to begin attaching it, the entire member began to tip over. The employee went to stop the main piece from tipping over and it landed on his ankle, fracturing it.

An employee was helping a coworker transport a tall palm tree with a mini skid steer. The employee was severely shocked by a high-voltage electrical wire above the ground.

An employee was retrieving a Christmas tree from a shelf using a ladder. He missed a step and fell to the concrete floor. He sustained injury to his head and wrist.

An employee was inspecting a generator whose radiator was leaking. He slipped, and a fan blade in the generator amputated his thumb and index finger.

An employee was operating an agricultural tractor during sugarcane harvesting. The employee sustained a lumbar sprain due to vibration or motion from the tractor.

An employee was moving a 3-ton condensing unit, strapped down on a dolly, out of a garage. The strap broke, causing the employee to fall backward onto the brick pavered driveway. The employee suffered injury to a spinal ligament in the neck.