Layne Christensen Company

An employee was stepping from a secured pipe on a trailer deck when he fell to the ground, leading to right-side distal tibia and fibular fractures.

Workers were drilling a water well. They were removing the drill pipes from the well with a block when the block went past the block stop at the top of the rig and broke free. The block fell to the drill deck and the bails on the block struck an employee, causing him to fall 8 feet to the ground. He was also struck by slips that were dislodged by the impact of the block. He suffered four fractured vertebrae and lacerations to the head and ear.

An employee was dismantling an overhead conveyor when the connection point for the rigging gave way and the conveyor fell, amputating the employee's left pinky finger at the first joint (just below the nailbed).

An employee was forming a footing for a water treatment plant. He was working inside a 4-feet-tall trench form and fell while crossing back over to the outside of the trench, breaking his right tibia and fibula.

An employee was inside a sewer hole and was turning on a jetting tool when the pressure caused the hose to whip around and strike the employee's lip and elbow.

An employee was installing a 15-amp breaker in an electrical panel when a 12-gauge ground wire touched the positive busbar of the panel, resulting in an arc flash. The employee sustained a second-degree burn to their left hand.

An employee was repairing an HVAC system in the drop tile ceiling of a conference room when they were shocked, causing them to fall from the ladder. The employee sustained burns to their right middle and ring fingers.

An employee was replacing a contactor inside an electrical panel attached directly to a press. The press itself was receiving power from another main panel. After replacing the contactor, the employee flipped the switch and an arc flash occurred, burning the employee's elbow, bicep, and neck.

An employee was attempting to switch a medium-voltage primary cable and install a 200-amp fuse barrel. The employee contacted the bottom of the switch gear cradle for the fuse barrel, causing an arc blast. The electricity entered the employee s left hand and exited his big toes, resulting in electric shock and burns to the left hand, arm, shoulder, and both feet. The employee was hospitalized.

On December 6, 2023, an employee of Duke Energy was working on a single-phase 120-/240-volt parallel service re-tap when a secondary flash occurred in an underground service. The employee suffered a second-degree burn to the face and was hospitalized.

An employee was moving a tensile strength test device with a dolly. The device fell from the dolly onto the employee's right leg, causing a compound fracture.

An employee fell while stepping off the tailgate of a pickup truck. The employee landed on the ground and suffered a broken left fibula and tibia.

On October 7, 2025, employees were conducting trenching operations for the installation of a new sewer line system. The excavator's bucket was detached and put inside the trench as it was being exchanged for a different-sized bucket. An employee entered the trench with a shovel to move some dirt located at the front end of the pipe. The excavator bucket shifted and slid, striking the employee s right foot and trapping it against the ground. The employee sustained a fractured right tibia.

Employees were working to dislodge a large truck that was stuck in a rut using tow straps and a front-end loader with the bucket removed. An employee connected the straps to the loader and truck and another employee slowly engaged the loader to close the coupler. The injured employee's arm became caught in a pinch point. The employee was hospitalized with a fractured arm.

An employee was lifting a piece of 30-inch line stopping equipment using a jack screw. A lifting eye weld snapped and the load dropped. The end of the jack screw then landed on the employee's heel and crushed it. The employee was hospitalized.

An employee was delivering materials. He was doing his pre-delivery inspection on the roof of the jobsite (a warehouse) when he fell through a plexiglass skylight. He landed on his feet on the concrete floor 14 feet below. The employee sustained fractures to his spine, left ulnar/radius, and right heel. The employee required surgery.

An employee was cutting cabinet trim using a table saw when four fingers on his left hand were severed, resulting in hospitalization and amputation.

An employee was removing packaging from a roll of printing substrate. The blade of their utility knife got stuck. The employee used both hands to free the knife and the blade partially amputated their left little fingertip.

A concrete batch plant operator was assisting with clearing spoil piles using a skid steer. The skid steer backed into a stationary screen plant. The employee's left little finger was crushed between the controls of the skid steer and the screen plant, resulting in a fracture and laceration. The employee's finger was surgically amputated.

An employee was standing on an extension ladder, using a torquing tool to remove bolts that secured blades to a rotor. When the torquing tool activated, its reaction arm came around and pinched the employee's right middle finger against a lifting eye. His fingertip was amputated.