Berry Global

An employee was stepping down from a two-step ladder when the ladder slipped out from underneath them. The employee fell and landed on a sidekick trailer jack, resulting in four fractured ribs, including two ribs with multiple breaks, and a pulmonary contusion.

An employee was performing a roll transfer on a turret winder. After indexing the turret, she was about to separate the bag at the perforation but noticed that the bag had not adhered to the new core. She tried to reach over the finished roll (which was on the rear spindle) to tuck the bag onto the new core (which was on the front spindle). Her hand was pulled into the front spindle, and her right forearm was broken. She was hospitalized.

An employee was reinstalling a 200-pound drive motor shaft in a mold machine, holding the shaft while aligning it and inserting it into the machine's shaft hole. The employee's left little finger was caught between a bearing on the shaft and the hole; the tip of the finger was amputated below the first knuckle.

An employee disengaged a shaft cylinder and in the process severely pinched her right index finger between the shaft and the shaft collar.

An employee was changing out the plastic core on a portable winder machine. After replacing the core, the employee turned on the machine and began to wind some material onto the new core. The employee's right hand then contacted the chuck of the winder, resulting in a right index finger fracture and partial amputation. The machine was not locked/tagged out at the time of the incident.

An employee was preparing a tank car for loading while chipping away solidified product in the manway opening of the tank car. A pressure noise within the tank car startled the employee, causing him to stumble backward and fall approximately 10 feet over the guard railing at the chemical loading rack to the ground. The employee suffered fractured vertebrae, a fractured right wrist and ankle, and a dislocated jaw.

An employee was installing an electrical tray remover from a ladder. As he was descending, his missed a step and fell 6-7 feet to the floor. The employee suffered a head injury.

Two employees were installing spray foam insulation in the attic of a new residential construction. The injured employee fell 8 feet from an A-frame ladder to the floor. The employee suffered lacerations, abrasions, and a head injury.

An employee was on a raised platform attaching wires to electrical boxes. The employee fell approximately 8 feet to the floor below and struck an exit sign on the way down, resulting in an injury to his face.

An employee was in a forklift man basket fixing a garage door opener when they fell approximately 8 feet to the concrete ground below. The employee suffered head and back injuries as well as kidney bruising.

A subcontracted engineer was advising maintenance how to make a modification to the embossing roll system on a new line. Maintenance was bringing the motor and gearbox down with a crane. The load shifted when it was a few inches from the ground. The engineer went to catch/maneuver the gearbox and the fingers on his left hand were crushed between the I-beam base of the gearbox and the concrete floor. A finger was amputated.

On July 30, 2025, an employee was assisting co-workers in using a hoist to position an injection molding tool onto a work table. As the tool was being lowered, the slide section shifted, trapping and amputating the employee's right thumb tip.

An employee was manually lifting a film roll when their right middle fingertip was pinched between the roll and a metal beam, resulting in a fingertip amputation.

At about 10:00 a.m. on July 13, 2025, an employee was cleaning the adhesive from running rollers using a rag soaked in cleaning solvent to prevent contamination. The rag was caught between two rollers and pulled the employee's right hand between the rollers. The employee sustained right hand crushing injuries, de-gloving injuries (palmer and dorsal sides), and fractures. The employee was hospitalized and required surgery. The machine was not locked out/tagged out at the time.

An employee working on a sheet line was removing masking from the underside of plastic sheeting that was being lifted by a vacuum lift. The plastic sheet measured 4 feet wide, 14 feet long, and approximately 1 inch thick, and it weighed approximately 300 pounds. The vacuum lost suction and dropped the plastic sheet onto the employee's arm, pinning it between two sheets and resulting in a broken right forearm.

After cutting a slab of beef short ribs, an employee turned to grab the pieces he had cut and his right hand contacted the saw blade. The employee sustained an amputation to his right index finger.

An employee was unloading a carpet pad from a truck when they fell from the truck dock to the concrete below, resulting in five fractured ribs and an injury to their left lung.

An employee was inspecting flares processes. The employee received burns to the front side of the body, face and arm from the flares.

An employee was removing plastic material from a production line when the machine cycled and amputated his left index, ring, and little fingers.

An employee was walking up a walkway to enter a building through the back entrance when she tripped over the lip of the cement ramp. The employee fell and sustained a fractured right hip.