Patterson-UTI Drilling Company LLC

On September 18, 2025, an employee was descending stairs on a rig floor when he fell on the third step from the top and landed on his right foot, which then turned inward. The employee suffered a fracture that required hospitalization.

An employee was standing on a piece of equipment called a K-brace, approximately 3.5 feet off the ground. He was working to assemble part of the K-brace. He was driving a metal pin with a sledgehammer and put the sledgehammer on the ground. He then hopped off the K-brace backward and struck the handle of the sledgehammer as he came to the ground. The employee was hospitalized with a laceration to his left buttocks and a fractured tailbone.

An employee fell onto a rig floor while a stand of drill pipe was being moved nearby. The employee had just braced himself, putting his hand out in front of him, when the stand of pipe was set down on the floor. It crushed the employee's left ring finger, resulting in an amputation to the finger.

An employee was standing on the ground while rolling a pony sub from the forks of a forklift onto a catwalk. The sub shifted and fell approximately two feet onto the top of their right safety boot. The employee was hospitalized with a fractured foot that required surgery.

Two employees were carrying a drill bit and installation tool to the center of a drilling rig floor. One of them slipped and fell, and the drill bit and installation tool landed on his left hand. He suffered an open fracture and partial amputation of the last joint of the little finger, as well as a laceration to the ring finger.

An employee was using a crane. The hook slipped and a fitting fell onto a finger on the employee's left hand causing a fracture and laceration.

An employee was transporting an 800-pound die on a cart from the tool room. The employee was pulling the cart when it struck a metal plate on the floor. This caused the cart to tip forward and the die to slide off the cart. The die struck the employee's left foot and their second toe was amputated.

An employee was using a forklift to load pallets of product on a trailer. He exited the forklift to adjust a pallet by hand. The pallet fell on him, resulting in an injury to the left leg.

An employee was lifting a 500-pound steel counterweight off a pallet using a magnetic hold jib crane. The counterweight detached from the crane and the employee sustained a left foot/toe fracture that required surgery.

An employee was using a pipe wrench to turn a 42-foot-long steel pipe on jack stands to weld the bottom portion. The pipe fell off the stands, striking the injured employee on his left shin. The employee sustained a left leg fracture at the shin area as well as a tibia fracture that required surgery.

An employee was stepping down off a 6-inch containment platform to finish loading his truck, when his right ankle rolled. The employee sustained a fractured tibia and fibula at the right ankle and required surgery.

A service crew was pulling a pump and motor from a well. After breaking a joint of pipe loose from another joint, an employee grabbed the chain tongs to prevent the pipe from spinning in the well, so the crew could continue taking it apart. The bolt that attaches the chain to the handle of the chain tongs broke, causing the chain to swing around and strike the employee's lower right leg. The chain severely punctured his leg and fractured his tibia.

An employee was working to remove a stuck fish tool from a drill shoe. Their thumb was struck by a hammer, resulting in amputation.

An employee arrived on location and loaded a blow-out-preventer (BOP) on a 1-ton flatbed truck. While standing on the flatbed securing the the BOP, the employee stepped into a void/hole on the flatbed surface. This caused him to lose balance and fall off the truck bed with his leg still caught in the hole. As a result, he sustained fractures to his left leg.

An employee was rigging up a location. He was using an Allen wrench to free up rotation and start the drawworks engine manually. The engine rotated and his left little finger became caught between the Allen wrench and the engine. The employee sustained an amputation to his little finger and fractures to his wrist.

After cutting a slab of beef short ribs, an employee turned to grab the pieces he had cut and his right hand contacted the saw blade. The employee sustained an amputation to his right index finger.

An employee was unloading a carpet pad from a truck when they fell from the truck dock to the concrete below, resulting in five fractured ribs and an injury to their left lung.

An employee was inspecting flares processes. The employee received burns to the front side of the body, face and arm from the flares.

An employee was removing plastic material from a production line when the machine cycled and amputated his left index, ring, and little fingers.

An employee was walking up a walkway to enter a building through the back entrance when she tripped over the lip of the cement ramp. The employee fell and sustained a fractured right hip.