Precision Drilling Inc.

An employee was working with makeup tongs (manual pipe tongs) to make them clasp. The top drive torque spun counter clockwise, causing the tongs to clasp and the snub line to pull tight. The entire pipe stand flexed and the pin end lost contact with the floor, skidding backward toward the injured employee. The tongs and stand of drill pipe struck the employee on their left side resulting in fractures to the left tibia, fibula, and ulna.

An employee was patrolling a store using an electric patrol scooter when they lost their balance and sustained an ankle fracture.

An employee was operating a forklift to move panels around the dock area when the vehicle struck a joint where the two floors meet. The employee lurched forward and struck his head on the steering wheel. The employee then fell from the vehicle and sustained a dislocated disc in their back, requiring hospitalization.

An employee was standing inside a semi-trailer when the driver of the semi-trailer pulled away, causing the employee to fall backward and strike their head on a steel dock plate. The employee suffered a skull fracture, a fractured L1 vertebra, a broken coccyx, a laceration/abrasion to the head, and a brain bleed.

An employee was riding an ATV, catching up with a stray cow to return it to a pen. The ATV tire struck a hole or other obstacle, causing the employee to be ejected and fall to the ground. His leg was broken and he was hospitalized.

An employee was driving a van in reverse when they fell out of the vehicle and landed on the ground in the parking lot. The employee sustained a fractured left hip.

An employee was stepping down off a 6-inch containment platform to finish loading his truck, when his right ankle rolled. The employee sustained a fractured tibia and fibula at the right ankle and required surgery.

A service crew was pulling a pump and motor from a well. After breaking a joint of pipe loose from another joint, an employee grabbed the chain tongs to prevent the pipe from spinning in the well, so the crew could continue taking it apart. The bolt that attaches the chain to the handle of the chain tongs broke, causing the chain to swing around and strike the employee's lower right leg. The chain severely punctured his leg and fractured his tibia.

An employee was working to remove a stuck fish tool from a drill shoe. Their thumb was struck by a hammer, resulting in amputation.

An employee arrived on location and loaded a blow-out-preventer (BOP) on a 1-ton flatbed truck. While standing on the flatbed securing the the BOP, the employee stepped into a void/hole on the flatbed surface. This caused him to lose balance and fall off the truck bed with his leg still caught in the hole. As a result, he sustained fractures to his left leg.

An employee was rigging up a location. He was using an Allen wrench to free up rotation and start the drawworks engine manually. The engine rotated and his left little finger became caught between the Allen wrench and the engine. The employee sustained an amputation to his little finger and fractures to his wrist.

A crew was installing drilled micropiles alongside an outdoor covered deck foundation. The injured employee was working the front of the drill when a loose section of casing dropped onto the tip of a rig wrench and pulled the wrench down to an embedded casing. The employee's left little finger was caught between the rig wrench and the embedded casing and was amputated above the top knuckle.

Two employees were working to change a tire on a mobile slasher saw. The slasher weighs around 2,000 pounds and is towed. Employee 2 was lifting the saw while the injured employee was placing a block of wood under the frame for support. The slasher then lowered onto the block and the injured employee's left thumb was crushed between the slasher frame and the wood block, leading to an amputation at the first knuckle.

An employee was using a metal shear when it amputated the tip of his right index finger.

An employee was using a crane to move a 44-foot, 3,343-pound I-beam. As the beam was moving west, it straightened out (north to south), beginning to swing south toward the northwest corner of a building. The crane then sent the beam southward, directly toward the corner of the building. The beam caught the tips of the employee's left index, middle, and ring fingers against the building. The last joints of the middle and ring fingers were amputated, and the last joint of the index finger was partially crushed.

An employee was standing on a step stool, removing the nuts and bolts from the frame of a solar panel that was being replaced. The employee's cheek made contact with a connector with damaged insulation. The employee was shocked, briefly lost consciousness, and fell to the ground, suffering an injury to the left shoulder.